General Discussions - 300ZX Related

Hi guys just a thought Ive just bought a set of G-Force coilovers and was wondering if i will need a camber correction kit for these? Anybody fitted coilovers have problems? :confused:

Can anyone tell me how to remove a standard leather gear knob from a UK manual. Have tried allsorts even as far as taking the surround out and looking underneath!! I thought it would be a standard screw in but is too tight for that even with glue. it turns a bit but then gets tight again. Am I just being stupid?!?!?!?

Very nice with '98/'99 spec rear spoiler. Didn't get a chance to see any more detail - but there can't be many of those in Braunton!!!!! ;)

Sunday morning about 11:00, silver import ...

Hey. My ConZult arrived on saturday morning :D What a great tool, highly reccomended. I have a knock sensor fault. Checked and re-checked wiring loom for continuity. Found breaks here and there so I by-passed the lot. Fault still there. Fitted a porsche knock sensor to the inlet manifold and connected into my new loom. Still doesnt work. Does any one know the resistance of an operational z32 tt knock sensor? Any help mostly appreciated.

Hello. I'm thinking of fitting a voltage stabiliser and need to know how :o :confused: .. Do I just connect the + and - cables/terminals of teh unit to the + and - terminals on the battery or connect the positive to the battery and the negative to the body or other earth ?? Thanks in advance. :bow:

I don't know if anyones interested, but with winter approaching. The heater matrix from a Primera fits our cars with a very slight mod to the plastic enclosure and about an hours extra work.....got to take the dash out though. costs less than 1/2 a proper z matrix have done 2 now, 1 being my own, spent a little more time doin mine so I could change it .... if needed without removing the dash again.the other I did last Saturday for another club member....did it in 61/2 hours. the matrix looks " more up to the job aswell, as it's 6mm deeper. Just thought I'd share this Pete :D

Hi All. I have a bit of a problem with the engine cutting out when its warming up it starts fine ,runs fine,until it it gets close to normal operating temp then it cuts out ,if I leave it for 1 or 2 mins it will start up fine and run well till the next time it gets cold then we start all over again. I have run conzult and it gave 2 faults , temp sens and maf so I cleaned the connectors and removed the apexi filter in case water in the maf could be causing the problem and refitted the oem airbox and filters. Now I am getting no fault codes and acording to conzult they are both working fine. But on the way to and from work today it did the same again. Ra…

Hi peeps, I need to do some tig welding on the car (can't line it up ya see!) The battery obviously! but do I need to unplug any other electrics that are susseptable to 150amps going to earth ??? Many thanks harve

Any one experience this before: horn comes on and off on its own, checked relay, checked horns and connections, all fine after a day or 2 and then usually around midnight when the neighbours are sleeping the f****ng horn goes off. I know the car has a soul but i can't be with her 24/7....lol. I've tried disconnecting the wires in the steering wheel but it still goes off, sometimes it plays a toot tooot tooooooooooot toot t t t t toooot toot tune which is driving me mad, only way around it is pulling the relay which aint easy in the dark but then i miss the cruise control. currently running it with the horns disconnected but now worried that the battery might dra…

:confused: i was driving my 91 NA Manual Z home i got on to my road and then boom, i heard a some weird noises as if something was caught under the car, i stopped got out had a look there was nothing there, but as i started driving slowly again I could hear a nasty grinding noise coming from the back of the car, as if my break pads had gone and the breaks where pressed. i jacked the car up i can turn the back wheels by hand with a bit of effort and i can hear that grinding noise, the break pads are still there discs look to be fine, oh and I noticed that the noise increases when breaking. Any ideas, anyone????? :headvswal

Saw a red 300zx going past the swiss cottage in santry at about half 7 on sat 29th oct. the car is for sale in the auto trader and have to say the alloys were lovely

Hello everyone Ive been ploughing through the search for info on wheel sizes. Most I could find was info on width. I'm after the profile size I would need to fit 17" wheels. I dont want to change the overall diameter too much. Would the off set remain the same too? Thanks Andrew

My son has a 300ZX which he has had a few problems with. One of the turbos failed. He took it to a garage that was recommended (in the west of England - where he was at the time). :headvswal - Nightmare. The garage replaced both turbos with recon units. But it is still not 'right'. Any recommendations for an independent 'specialist; in Kent / Sussx / Essex? Personal recommendation from perople who have had experience would be great.

Hi, does anyone know off-hand what the diameter for the handbrake is when the cover is off? I had a hunt round and found THIS nugget on removing the stock one and as I have lost my verniers and frankly can't be arsed to strip it until I have to, all help would be most welcome :hyper: Alternatively has anyone tried fitting one of THESE? Typically enough it's the ones I like that look as if they might be too small :(

This morning, M40(S) between J12and J11 - chasing each other. Got a wave of one of you when you passed me. Front one was blue (standard looking) and the rear one was silver with what appeared to be a wide-arch kit and big rims ... Couldn't see very well due to spray on the road. Anyone on here? Dan

Anyone got jwt mild cams or similar??? will they make much difference on a mildly modded engine? Who can supply these or other similar spec ones in the uk? cheers peeps!

I may be missing the point - but wont this make the ride unbearable? http://cgi.ebay.co.uk/SKYLINE-GTR-GTS-SILVIA-200SX-300ZX-Bushes-Collars-DRIFT_W0QQitemZ8011191091QQcategoryZ23013QQrdZ1QQcmdZViewItem

Need a little advice, fitted a set of portfield pads on the weekend, when i drove the car i noticed a grinding noise at low speed or when i was slowing down. Had a check and found that my discs were wearing a groove into the pads. now i knew the discs were warped when i fitted the pads but i thought the pads would just take the shape of the disc? Do i need to buy a pair of discs or should i just let them wear in a little more? If i need to purchase discs what would you guys recomend? Thanks Aktar

Hi, I just wanted to know If somebody can photo shop these rims for me on a 300ZX TT. A black one if you can. It doesnt matter. These are the rims, Stern ST-2. Put 19"s on them. Or 18"s. Thank you

http://www.streetracingmania.com/drifting4france/forum/viewtopic.php?t=77 some nice bits on it though ;) smithy Okay scrap that, just noticed chunks post in the other section, dohhhhhhhhhhh :o

hi i see a lot of people talking about codes like code 33 and how many time the light flashes to tell u whats wrong with the car i have a 300zx n/a 1992 do i have a Diagnostic tool

Quick question. When I'm turning right, say on a roundabout, the handbrake light is coming on. As soon as straighten up it goes off again. Don't think it's happening when I'm turning left. Just started a couple of days ago. Any ideas?? Cheers Steve

Does anyone with either the doolz or the JWT twin pop setup know what their MAF voltage reading is at WOT? I don't think the workshop manual provides any information apart from the voltage at idle. Cheers Steve

How much more do the tt front calipers pretrude than the na calipers. Also are the discs a different diameter? If anyone has done the conversion and knows an exact measurements, it would be very handy. Need this info to decide whether the wheels i want will clear the calipers. many thanks