General Discussions - 300ZX Related

Does anyone supply a complete kit needed for this ? I,ve looked on the traders sites and can,t find owt :sad::sad: Cheers

carried out a diagnostic and got code 12 and 13 when i disconnect the maf the revs pick up, is this showing that the connection is ok but likely a faulty unit? also the coolant temp sensor, when i disconnect it, the front fan kicks in then goes off when reconnected, does this show that the connections are ok but possibly faulty sensor? also done the o2 sensor test while i had access to the ecu, the ecu is an impul z32a-1262 if that means anything to anyone? i put this as the instructions i followed said with each sensor test it should blink over 5 times in 10 seconds but on mine, each sensor test flashed the light on for 15 seconds then off for 5 seconds th…

Ok When The car is started from cold, rev's around 1500. Once warmed up, the rev's will drop to 1200, and then to 800 when she wants, doesnt seem to be consistent. She's an N/A if that makes a difference Any suggestions. Assume the above with aircon off!!

Jimmer and FunkySi came down yesterday, a big thanks for all the help!!. The timing belt is now on and Jimmer also put my new cams in, really posh new intake sprockets and new turbo oil feeds. :w00t: There are still a few little bits to do on the Engine before it gets its final fit. But it had to go in the hole so I can get someone out to make me some new power steering and NOS pipes up.

Guys I need to fabricate some bits to get my Recaros to fit into my Zed. I have the universal slider and fitting kit but its not even close. They supply them with a load of steel to help you fabricate something!. Anyhows im going to need to do some welding can someone please let me know what I need to buy ie, what welder, wire mask etc. Im not looking for proffesional stuff just something easy to use and learn on. thanks

A big difference in looks don't you think:ohmy:'

.....easy is it??

Just bolted seats back in plugged in after checking fuses [ok] started car warning light went out power steering back on tried indicators and warning light came back on and no power steering cant get belt light back off !!!!! Any siggestions or where i can find good auot electrician in hampshire

Seen you today, mirrors folded back, nice shiny red zed, parked up in Croston.

HI Thanks for replies still got warning light on for seatbelts no indicators or power steering im baffled at mo was looking into fuses but everything is in japanese does anyone know if the three are linked, i thought i saw a thread with a translation of fuse cover on but cant find it only got owners manual and all that says is to change fuse if its gone, if anyone can help would be appreciated its doing my head in at mo

Jimmer and I spotted a red Z32 heading West bound on the M27 about 10am yesterday. Think is was a JDM.

Was behind me saturday at 5.50pm all the way through town to Middlemore estate where you turned off to go further in to estate, i was taking daughter to work at the Pub nearby.I did put me hand up to you put not sure if you noticed. Tony

Shock Absorbers Wanted - Standard(rear) or uprated(all Around). 1989 Z32 TT LWB....any pointers?

do the coil pack always make a clicking noise. didnt notice when i got car. just asking to make sure cheers

Hi mate, Did you sell your z.? Im still interested in your wheels. Cheerz Chris

hi I'm doing a manual conversion can i put a direct clutch line form the master to the slave

about 6.30 pm today

Manual shows two adjustment screws, To move up/down, L&Right, on each headlight, States adjust dipped beam ist, Then gives info on adjustment to main beam, no info on screws for this ? same screws ? What to do, adjust main or dipped, only ? Recently fitted H I D conversion, causing a bit of upset to other road users.

hi all my tt's runing a few mods(ecu decats exhaust induction) and i have recently upped the boost 14psi, the car will run fine for about 20 mins at this boost then drop in to safty boost, when stoping the engine for a while and re starting the car will run on full boost again for about 20 mins the the same thing will happen. i havent checked the ecu for error codes yet. any ideas? thanks nick

My mate found this and told me about it - got some good 300zx footage about 3:55 in, this is the whole movie by the way so will probably be more bits but I've not seen it yet! :rockon::clap::punk::thumbup: will need adobe flash player to watch. http://vidreel.com/video/NTk0ODg0/ enjoy! :thumbup1:

if my boost gauge boosts fine straight up to +7 and stays there while accelerating hard, does that mean i have no boost/vacuum leaks or could there still be a leak somewhere?? my idle is a little rough, checked a few connections, seem fine, the yellow temp sensor brings the very front fan on when i disconnect it then goes off again when reconnected so that connection seems ok, maf disconnected increases the rpm so that seems to be working ok, put new plugs in and had the throttle valves cleaned. will try an ecu diagnostic tomorrow to see if any codes are registered. where is the tps?

Do 18'' 350z wheels fit my 95 300zx tt, think stud pattern is ok was wondering about the offset and spigot diameter, many thanks

Anyone help been out most of day with passengers front and rear when seatbelt warning light came on all had belts on it also took out power steering and indicators thought it may be due to passenger seat being lifted to let person in back out, had look at plug under seat looks ok . Any ideas appreciated.

Going to have a new clutch fitted with a light weight flywheel , need a new prop bearing £125 , so rather than spending on a prop bearing was thinking of putting it towards a prop , a lightwaight prop [ ally ] , any one had any negatives on these , ie the fit extra ?

Battery went flat, put key in egnition shut the door put jump leads on and the door locked, unable to get in the car and I only got 1 key when I bought it, how can I get in? Any help please Mark