Everything posted by phutumsch
-
New exhaust....
Nice Richard, similar to mine, I went for slash cut.
-
New exhaust....
- Happy Birthday Redwine300
Happy Birthday ?.- Happy Birthday Iangreenfield
Happy Birthday Ian ?.- What did you do to your zed today?
Methinks, they charge £750, no matter what full system you choose ?.- 1993 TT LWB in Black
?. Knob is fifty trillion times better.- Selling my Z
I read as if you're wanting 15k. Some more pictures would help. If it's as clean as it looks then I think it should command 15K, buyers of these will be limited, patience might be needed. Not a fan of you putting 2006, certainly state though that this was imported date, although this is unlikely to be causing a problem. Is it an early 1994 ?- SMoked Side Repeaters
T10 or 501.- SMoked Side Repeaters
Not for me is the smoked but don't forget you can smoke them yourself with an aerosol spray. Wonder what smoked orange ones look like ?.- Front and side passenger indicators not working?
The relay is near the pedals, fyi. Both the rear indicators are working ?- Giving it a new lease of life- pic heavy!
Yes it was much quicker than yours and the driver was better ?.- 1995 Silver Series IV Slicktop Version S - Taking To Another Level
Thanks for the kind words you cock !! He's right though I don't drive it, wish I could tell you more, I will say this I am thinking of putting it on the road from May for 6 months.- Wheels!
Your front is basically a 8.5J +26 poke wise, possibly giving you a 10mm spacer option for very flush/brake clearance, a 9.5J will sit closer to the suspension strut, may be some rubbing on full lock. The rear is not a problem. The front is very near but ultimately the decision is yours.- Wheels!
ET +44 and 8.5J is fine for the front. The lower the positive ET gets to 0, the more it’s going to stick out. You don’t ideally want a 8.5J although you could for the rear, wider the better for the extra 25mm tyre width, that a 9.5J will give you.- Rear 300ZX panel
These I'd call aftermarket are not a patch on the original OEM inverter that Altia supplied to that rear panel, massive size and weight difference, cheap Chinese rubbish you could say but I don't see an alternative, it's to convert 12v up to 110v btw. Putting in a simple in line fuse will do no harm, just have to hope this is the fault and not the red sheet inside, does point it being though.- Rear 300ZX panel
12V Adapter Driver Controller Inverter For 1-5M El Wire Electroluminescent Li C+ | eBay Ebay, something like that. Cheaper but a longer wait, if you want it shipping from China. The cig plug can be snipped off, the positive and a ground/negative wire will remain. Is there a lump on your 'block' where it might have blown ? A loose connection ? And check that the inverter is getting 12v and I'll presume this is when you turn your sidelights on.- Rear 300ZX panel
You have the original green light up one ? You may need a new 12v power driver/inverter, they should buzz in operation.- Wheels!
I've a bit more time to answer now, the driftworks link provides full sets which I believe are in stock, I had to wait 9 months for mine but it was Covid time, I bought all my four individually and specs are above. Full sets do tend to be staggered, so that's usually a 8.5J and a 9.5J rear. The fronts are likely to have a straighter face, 'R' fitment iirc, so they may not be just as pretty as a concave rear wheel, 'A' fitment again, if I remember correctly. You'd be better following one of us with similar spec wheels, at least then you'll know they'll fit. A 9.5J ET20 will not fit on the front, too much poke, it will fit better on the rear, just, on a standard arch, you may have to stretch a tyre a little, so instead of a 275 width, go a little less but why ? Get the correct offset straight out of the box and more rubber down is my opinion. 8.5J ET20 is more like it for a front wheel but you've got brake clearance to consider, so that leads back to the 'A' and 'R' fitments I have mentioned, lots to consider.- Wheels!
There’s some things you’re not considering but that’s for another day. Check this out which came to me the other day via email https://www.driftworks.com/wheels-and-accessories/alloy-wheels/work-wheels-uk-in-stock?utm_source=Driftworks+Team+Newsletter&utm_campaign=1974c5ce34-EMAIL_CAMPAIGN_2018_05_21_COPY_01&utm_medium=email&utm_term=0_c573cd9b3d-1974c5ce34-260853914&mc_cid=1974c5ce34&mc_eid=a7571bae85- What did you do to your zed today?
His wallet certainly wouldn’t ?.- Happy Birthday Joely P
Happy Birthday Joel ?.- Modified '90 Nissan 300ZX TT Manual in US Auction
I like to think mine's like that ?.- Happy Birthday Phutumsch
Thanks guys, appreciate your kind comments, well most of them ?.- Happy Birthday Phutumsch
I don't ?.- Happy Birthday Phutumsch
Oh my, my favourite picture ?. - Happy Birthday Redwine300