General Discussions - 300ZX Related

Can anyone tell me how long the lower fuel pipe from the FPR to the fuel rail is? I chucked my old one out without thinking about it! lol

http://www.driftworks.com/forum/parts-sale-private-sales/133969-300zx-z32-parts-sale.html may be of interest to someone. :thumbup1:

Hi all i got my Perspex strip today from Mjp, great service as always!!! (thanks Mike) Just on fitting though i notice it has the clips to fit in on the tailgate bit but i’ve heard they need sealing on to with some sort of bond? what have others used ? thanks Chris

http://cgi.ebay.co.uk/nissan-300zx-rare-stereo-/320635890270?pt=LH_DefaultDomain_3&hash=item4aa7636a5e Been outbid on this original stereo any idea what one would be worth I have less than an hour to make my mind up:biggrin:

fitted some HIDs a few weeks back and it was the first chance i had got to go out in it last night. i have since looked at adjusting the beam pattern had succesfully adjusted the height bringing the passenger side down a tad, but my biggest problem is the beam pattern on the drivers side. Passenger side when parked in front of my nice white garage door emits a nice white beam into a noticeable spot. Drivers side no matter how hard i fiddle with it is just a splayed pattern with no light spot? how can i overcome this or adjust it, it annoys me every time i return from a drive in the dark. The drivers side is also slightly yellow but i would expect thats…

Iv converted From na to tt but retained the old clutch and flywheel with the na gear box, I'm now fitting a tt clutch and flywheel with my NA gear box, I'm aware it will need grinding out and the starter will need shimming out. There was an Image posted by someone that specifically discribed where I needed to grind, I have a bad back and constantly repositioning it whilst it's up in the air will ruin my spine, will be doing it tomorrow so any help will be greatly appreciated.

Hi All, Righty! I picked up a new diff off Gonzo's breaker and am half way through getting the knackered diff off my car!! Question is - is there anything I should do to the new diff that is going on whilst it is off the car? Thanks, Tom!

he asked a question about wheels fitting from a skyline im just wonderin what parts are interchangable from skyline to zed..bar brake discs i.e will the tien strut brace for a r33 fit a zed they look the same but would they fit a zed my point is we should make a list of nissan part know to fit a zed that come from other models ill start p10 heater matrix(bear in mind that after 95 nissan chanced the p10 to a fully molded tank)

see them clear lenses you have on your rear bumper wher'd you get them

think i might have done something daft!!put charger on my battery but didn't disconnect it.could this have damaged the alternator?

Hiya Guys Just looked at there site and now have a new bit called pit lane. They have some nice bits at I think good prices. Silicon hoses, air filters etc. http://www.eurocarparts.com/performance-and-styling

Do amazon sell everything??? http://www.amazon.com/NISSAN-ENGINE-WIRING-HARNESS-300ZX/dp/B003162UOO/ref=sr_1_1?ie=UTF8&qid=1294350980&sr=8-1

I decided to check my ignition timing today and found it to be about 27 degrees before top dead centre.:sweatdrop: Slackened off the 3 bolts securing the crank angle sensor and rotated it clockwise until I achieved 15 btc. My only worry is that I had to use all of the adjustment to get it. The strobe I am using is a pickup type that I connect top the + and - respectively and the pickup to the looped wire at the power transistor unit. I seem to remember reading that this method may give a false reading of up to 10 degrees error.:ohmy: Could anyone advise please?

i have just got some seats and as there wasnt eletric there origanly i was wondering were the wires would need to come from i also have the relays for the heater parts in the seats would they needseperate wires or not any help would be much appreciated cheers richard

How much water should I expect from the exhaust? I have a turbo UK model and after a couple of minutes working under the bonnet(while at tick over) I can hear her gurgling quite loudly and when I rev her up she splutters and pops and almost stalls,:helpsmilie: while at the same time spits what looks like a good pint or more from each side over the garage floor. Surely this is excessive?

Hi all, Sorry i've not posted in a while! As the title suggests, I had a bit of a spin a couple of weeks ago due to a pillock pulling out on me and getting stuck halfway across the road. Luckilly the only battering was from the untouched central wall of snow as I went over it sideways. However ever since it's been blowing and as I hit the 3500rpm range it really does make a racket, sort of a rattly higher pitched noise... Anyway I took it to a friend who got it up on a lift for a quick inspection. We couldnt find anything that was loose the only thing that was bound to be making the noise was what I think is the exhaust recirculation pipes? Perhaps? …

Well nice to see this place is still ticking along nicely. I havent had my zed for many years now however the old man does still have one. He has decided he is pulling the engine to do the head gasket and has asked what else should be done ideally while its out. Things that are easier done while its out and then you can rest in the knowledge that its done. If someone could give us a list of stuff then I can just pass it onto him and he can decide what to do. Also he needs a new knock sensor as he has broken the connector on his if anyone has one. Ta Glyn

Took the Alfa for an MOT and there was a black manual twin turbo there it was in Universal Motors in Edmonton anyone on here? I havnt seen it around before :whistling: .

Hi all, I'm looking to use these caliper relocation brackets to upgrade the disc size to 324mm, Just wondering everyone opinion on them? Worth it or not? :confused1:

PLEASE help, does 10j offset et10 wheels all around will fit to my tt 2+2 ? Those wheels is from skyline r33 its fit to stock aches does this will fit to my 300zx?

Just had a look through this site after saving it last year,they have some fantastic zed stuff on it from some exclusive companies like Project Mu.Clutch and flywheel section is huge.worth trawling through i reckon http://www.horsepowerfreaks.com/

on way home tonite warning lights came on ,dash pod went dim & engine started misfiring.after abuot 5 seconds & me dipping the lights all went back to normal,would lack of power in battery cause this?

how easy is it to remove the alternator?

My Toad keeps chirping to tell me the boot or bonnet isn't closed, its obviously the switch. I cleaned and checked the bonnet switch, seems fine, so must be the boot switch. But where is the damn thing? :confused1:

Hi guys ,me again, after taking the rad off the car, a lot of coolant oil came out and i was wondering how to fill it back up and with what thanks in advance Daz