General Discussions - 300ZX Related

What is the yellowtipped sensor, besides the water temp sensor on the front water hose. having a slight issue that with it connected, the revs are high, with them off it drops about 4-500rpm.... but no other changes?

While removing the old wings to fit my vented ones i noticed two bulb holders for the side lights ! Whats the other one for that is tied up ?

as title the interior will be back in tomorro is theyr any checks i should do..since the dials and everything has been removed will i need to reset the ecu or anything and if i do howd you do it? cheers

Ok, I've removed (by sheering off and chiselling) the two obvious bolts that hold on the OEM spoiler. I'm sure I've seen a pic somewhere of the spoiler removed showing many bold holes, but I can't find anymore bolts. So is it held on with adhesive, do I simply rip it off now using force, maybe heat it a little first? I'm sure this must have been asked before but not finding anything with the search.

Hi guys been a while since i been on here someone might remember my 300z's engine went last year after running high boost i posted a video of the nosie the engine was making. Anyway i had a look under the car today for the first time. I was surprised to find the leak in between the engine and gearbox their is also a shard of metal lodged in between. And 1 of the bolts that holds the box to the engine is gone literally blown off with just half a thread were it once was. Any ideas here is it the main crankshaft bearing gone?

well i took the car off the road in december 2009 and the most it has went since then is down to my dads garage when i was going on holiday. but im just back from my mechanics and got it booked to go in on the 12th march to get all checked over since its been sitting so long and get its new mot and since i was up there popped into the bodyshop so its getting its last few little bits done when its up there. going to start on the interior next weekend and start ripping out my old ice install and building my new one. also got my chrome fuel rail to fit, my new locks and ignition with titanium key and refit my dump valves

getting the tailgate area resprayed shortly and for best job wondered how easy the rear windscreen seams come off ?

can i remove this or do i need it cus i dont no what it is??? some thing to do with the fuel??? [ATTACH]57893[/ATTACH]

Hi all, Have the anti lock light on all the time, have checked the ecu and its code 9 - motor / relay. Have changed the relays and still the same, can anyone tell me where are all the fuses that are connected to ABS? On another thread someone mentioned a 30amp fuse? any ideas greatly appreciated. Cheers Garry

Southall, near lady margeret road.

Guy,s, Do I need to remove the water pipes to remove the Cambelt covers ? Any advice on removing them greatly appreciated Cheerz Chris

Hey, When my car is cold in the morning, I find putting it in second (sometimes third) notchy and there is a noticeable crunch. I fitted a new master clutch cylinder a few weeks back and wonder if it needs adjusting at the pedal. Just wondered if its normal to have a notchy / crunchy gearbox until in warms up?

What different dials are there for the zed? I've saw some beautiful looking Greddy ones etc. with strange blue glows to them! :drool: Any pics or links to some would be appreciated :thumbup1:

Hi all, Im looking to replace the down pipe bolts that bolt to the rear of the turbo im guessing it dont have to be a special order? Where can i buy them from or does anyone what type or thread they are? Thanks Dan

is it any one on here 8 oclock in B+Q car park in wakefield red and standard apart form twin exhaust !!

Got my Slicktop back from Mark (Silverbullet) today. Had the eliminator kit fitted, and the remaining bushes uprated to poly ones whilst the hubs were off. What a difference!! :gunsmilie: The car now feels and handles amazingly, I am so made up with it. What with these fitted and a full four wheel allignment again it is an absolute dream to drive :cool2: Massive thanks to Mark for yet again exceding all expectations. Fantastic service buddy. My suspension set up now: MeisterR zeta S coilovers DW adj Tension rods MeisterR (cyberspeed) front camber arm MeisterR (cyberspeed) rear camber arm DW total HICAS eliminator DW upright/cont. arm poly bushes …

Does anyone know if the non digital heater and a/c control pod can be replaced directly with the digital one ? My '95 has the non digital (oddly nissan thought it a good idea to go backwards ?) and I would like to swap over to a digital one if its not a major job !

Hi all I'm after a bit of advice i think Ive seriously been cheated here and not sure what can be done. Late may 2010 i was after a set of wheels for the zed so i could take the car off the axle stands and carry on with the build. I also had to change units so this would make things alot easier for transportation. I called a well known company for the brand of wheels i wanted and went for a package deal that was Rota GTR'D Wheels with 235/40/18 and 265/35/18Toyo T1r tyres and light weight nuts. The guy in charge of the wheels department gave me 5% discount and also included free delivery which is normally £15. The total came to £1510 which i was happy with. …

Hi all, As above i need to get a front bumper resprayed, but it is flexible polyurathane, so what do i need to use to ensure that the paint won't crack and flake? I have been told to use: Flexible primer, then normal paint, then flexible lacquer.... Firstly is this all i need? and secondly does anyone know where i can get some of the flexible stuff? I have just had a quick look on ebay and googled it but no joy.... Any ideas or suggestions would be gratefully recieved. Cheers in advance Pabs

cant seem to find the other connection for this! it comes out from the ignition key barrel as you can see in the pics anyone steer me in the right direction please :detective: dan.:confused1:

if the bushes are worn in the front torsion bars will this cut the tyres out ie:same as if tracking was out?

Just found this, like britians worst driver, even better using a zed. Nice and tidy to start with. Watch from start, zed is on until 13 mins. These people shouldnt be driving anything let alone a right hand zed.:no::no: Funny...............

You were heading south exiting a roundabout I was entering it heading north. I only caught a glimpse of you as I looked right to enter the roundabout so you might not have seen me in my grey LWB.

after losin some hair and a wee bit of crying in a dark room iv finaly got all the bits i need to sort my heater problem the cooling unit is leaking as well.as there is no belt on the aircon pump can bung the end of the pipes in the engine bay or can i do a bypass like the heater bypass or do i need to remove the full system im gonna say at this point that iv never used aircon ever

Where to buy good engine rebuild kit ? And What guys you can say before I start a rebuild, what do I need or how to do it? What parts I can change to get more bhp example like under pulleys? please give me some advise guys. Is this list enough to rebuild engine? 1. Full Gasket Kit 2. New Nissan OEM Rings and Bearings 3. New Nissan OEM Oil and Water Pumps 4. Timing belt anything else?