General Discussions - 300ZX Related

1. 'black' getting juice from the garage opposite the golden ball in Wycombe. Reg GLENN! 2. Pulled up nose to nose outside Activity world bletchley. silver with irish plate. 3. & Jez's parked in his garage! cheers for the stuff mate. By the way you were right she grumbled all the way home! LOL, should have took the van. ------------------

I'm looking to get a PDA and am probably going for an ipaq 3870 because it has bluetooth built in. I want to use my home broadband connection to surf on the PDA when I'm elsewhere in the house. Does anyone who knows about these things have any comment on whether this is a good choice or whether there are alternatives I should be considering ? They all seem pretty similar from what I've seen. And does anyone know a good cheap source of PDAs - plus a bluetooth adaptor for my home PC ? Thanks as always Dave

hi guys just a quickie ,i need some glass for my nissan which i sourced from courtesy nissan, namely a driver side quarterlight and passenger door glass. they say it is usa spec and not sure if it will fit , any experts out their who know.i have a swb , jap spec 300 on a 90 plate. any help appreciated, thanks steve.

Fitted this to a lucky customer Zed yesterday..very nice Jeff TT [This message has been edited by Jeff TT (edited 01-09-2002).]

Black 1992 TT Auto import for sale, full Jap service history. Stillen induction Kit SS Cat free front pipes Mongoose tail pipes Lowered 40mm Stillen rear wing Illumionated rear panel Alpine component speakers Kenwood ICE 400BHP 17" wheels (235F 275R) New PTU (series 2) fitted, always serviced and requires nothing. 62K miles for more pics see rides section. £5500 016973 51677 (Cumbria)

Now she's loosing bl!"£$ s water. Not vast amounts, say about a cup full over a 50 mile return trip. Water also bubbles a bit when you blip the accerator (both radiator tops off). Doesn't seem to be much pressure in the coolant system either since I can easily compress the hoses with my fingers. According to ConZult the temperature is rock steady at 80C when warmed up. Could this be the water pump or those pesky little short hoses. Problem is I can't see any water dripping when she's idling on my driveway. This has got me mega worried. Could it be water getting into the combustion system? She's a smooth as silk when running although low on power for a number of other…

Available now,these are Cybercrafts own design they force the air through the rad instead of it escaping over the top,so they will allow the car to run at a cooler temp. Have no idea how much they are,my car was used just to make sure they fit.mail him at smithy@manx.net

Drivers side (RHD) top link is hosed - anybody have one lying around that is good - available for a reasonable sum? Perhaps if you have fitted a camber kit recently!! Any help appreciated - MOT [due] next week! AndyGP

Hi, On mj Jspec zx, i have a rocker type switch next to the digital clock (which by the way does not work, are these easy to fix? as it would be nice to have this working!) There is no picture or label next to the switch... Any ideas what it does? Thanks Barry

V plate November 99 model, Manual FSH 42000 miles Red Immaculate 14 months warranty Need to sell so i can buy a Zed any info needed plz email me or give me a ring 07775 850615 Photos are in my rides section Thanks Chris [This message has been edited by Chris0r (edited 01-09-2002).]

Got myself a Z over the weekend but seems to have 2 probs. 1. Speedo doesnt always read correct, but after seaching the forum i have an idea what to do. 2. There doesn't seem to be that much power in 1st and 2nd. I'd of thought the revs would rocket up and ud accelerate hard. My rover 620Ti i think accelerates harder up to about 50. Any suggestions? Thanks Rob.

I'm having a problem with my z in that when im driving the car is like "jerking" especially going uphill. I've checked the usual things oil, fuses, etc. All seem to be ok. Anybody have this problem before. Please help lads. I'm a bit worried about driving the motor. Could it be low oil in the gearbox???

My exhaust is starting to blow, damaged caused by high speed bumps I think. It was pointed out to me when I got my MOT. However when looking at it, it looks more down pipe than exhaust. How far back does the down pipe go? If it is the down pipe, and I have to replace them, should I go decat or not? In the end is the damage it does not worth it? Stuart

Where can I find info for removal of the intake manifolds? My engine has a lot of miles on it, and I get the feeling there's still a lot of junk in there that I'm missing. ------------------ --Maxx

hi, just a thought might be well wrong but mine started to make a funny noise.so on closer inspection found a pipe had come out of its holder/fitting,this pipe comes from the aiv's up to the inner wing its about 1/2in diameter and goes to the inner wing like a breather?its doesn't have a pipe on the other side(engine bay)which you cannot see anyway covered by fuses(drivers side) but after i had connected this pipe back into its proper place the noise when't away! This pipe is easiest to see if you take the wheel arch liner out and look up to where the side indicator is then look across to the opposite side??? sorry for the shite desription, --hth-- --neil--

Fook me I'm pissed but she had the most fantastic figure and offered it on a plate and I had to be home for a miserable bitch who only knows how to open her legs for a doctor every few years... Sob Fuuuuuuuuuuuuuuuuuuucccccccccccccccccccccccccckkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkk! (bet that's not in the swear filter ) LMFAO How come I'm such a stud? No sarcastic comments please... asking for it big time! LOL

ive been thinking... dangerous i know but here goes.... If an oil is fully synthetic, ie completely man made then it must contain no real oil ie the crude black stuff that comes out the ground. so if it doesnt contain real oil, then what is it made of? nelson over to you.

I keep hearing about these companies ? Could someone please explain what services they offer along with addresses and phone nos.? I've heard they're cheaper than the z centre ?

I can't find any. I want to see what they look with one, as I think I want to get one. Anyone know a link to any pics ?

I have a slight oil leak. I am thinking this may require engine removal to sort it. If engine out was necessary, for this or any other reason, WHAT MODS WOULD BE WORTHWHILE DOING AT THIS TIME ? Note my engine is stock, but I would like to mod it at some stage - exhaust/airfilter/ECU/exhaust wrap/etc.? MY plan so far with my Z has been to wait until something major needed doing before starting serious engine mods.

Id like to thank Jeff for all the hard work hes done for me over the past few days, what some of you dont realise is Jeff was checking the White L plate Zed out for me which in the long run (or most probably short) would of cost me a bloody fortune, Jeff drove a long f**king way to see this car for me b4 i bought it, to find out its a wreck and when he posts it in forums to help people out all some of u do is slag him off, Jeff went well out of his way to help me with this car inspection and posted it to help some people who r newbies out, Yes i have payed Jeff (well as at the moment i havnt And jeff has not once asked for the money which he will get asap this week),…

For anyone who has or is suffering probshaft vibration, changed another centre propshaft on a customer`s car and remembered to take a picture of it. As they are mentioned a lot thought a picture may help visualise the problem for anyone who has not seen one, this one was wrecked and the excess movement was terrible, no wonder it banged a bit, all ok now though.Except the £150 Nissan price for the bearing kit!! Jeff TT

http://www.300zx.co.uk/forums/ubbforum/Forum5/HTML/001304.html

http://www.300zx.co.uk/forums/ubbforum/Forum5/HTML/001304.html

i dont want to pay much,but im after a zed bonnet,wing mirrors,fan shroud.happy to arrange collection and pay a small fee. thanks jay