General Discussions - 300ZX Related

A rare machine for almost £19,000 Prices are strong guys. https://www.ebay.co.uk/itm/294326293378?hash=item448736d382:g:q0UAAOSwPudhEj4~

Hi chaps, Does anyone own a Haltech ECU ? I've bought a Dual Channel Haltech Wideband Controller (WB2) to connect via CAN to my Link ECU. The difficulty is the Haltech WB2 requires the firmware updating to support this. I did not know this and was informed it was compatible! Would anyone be willing to receive my Haltech WB2 to upgrade the firmware on it via a Haltech ECU? I'm just shy of sending it back, as I don't know anyone with a Haltech ECU. Anyone willing to help out would be much appreciated, or recommend any options! Many thanks, Stuart

My speedo meter isn't working well, it's jumping up and down or says I'm driving 50 when I actually drive 30 miles. Also the power steering works only when I'm parking, with higher speeds it's not doing anything. I was hoping to fix this by replacing the speed sensor, so I did, but nothing changed. Anyone has an idea what it else can be? [url=https://postimg.cc/TprQ0TqP][img]https://i.postimg.cc/GhfNc24v/DSC03462.jpg[/img][/url]

Hi All, I'm hoping that someone can give me advice on how to proceed to get my car legal by showing the correct mileage. I know it's a long read but bear with me on this please. In 2007 I bought a rundown 300ZX from a dealer called Redline Autos based in north London, I think, (and who magically disappeared in 2008) for £2000 knowing it had no MOT and needed work. The mileage shown was around 55,000 KM's - which should have set alarm bells ringing as the drivers seat bolster was worn but I wanted the car. I spent a fortune during 2008/9 getting the car up to scratch, interior/seats, bodywork/spoiler, tyres, windscreen, exhaust etc., while trying to keep the…

Has anyone fitted one themselves? I can’t see how it fits, it’s an inch higher than the original cover it catches lots of pipes and cables. My fuse covers fitted over the originals, so tried that, wouldn’t fit. ?‍♂️

Can anyone please point me to where I can buy replacement bonnet struts for my 1988 300ZX 2+2 auto - thanks

Hi folks I’ve seen this car for sale on eBay, does anyone know about this car, the owner has had it for a number of years

Has anyone had any experience with this company

Hi my friends as you know iam on the hunt for another zed, I’ve found a couple , but need a bit of advice, first I’ve found a t/t auto jap spec it’s a 1994 model,guessing that makes it a series 2? It in white and a lwb it’s not on English plates , it’s kHz which I believe is Channel Islands, it’s had 2 plate changes in its life , the current owner has said the last keeper did the cam belt but unsure about the water pump, it only got mot till December , and is asking £6k for it, no2 is a uk spec on a k plate in black, got power seats and heated as well, and got the original sound system , the owner brought bit from Bedfordshire a while ago , but they say it needs a ne…

I will soon be fitting a Tein EDFC Active system to my Z. It has a controller and a front and rear motor driver module, each of which need a 12v feed. The motor drivers speak wirelessly to the controller, which will be situated somewhere on the dash. However they do need their own power feed, with one module (probably) in the engine bay and another towards the rear of the car. So I need a 12v feed at the front, centre and rear of the car for the 3 devices. I already have quite a few things tapped into the 12v ignition switched radio feed and I have read warnings about this feed not being the best anyway - so I do not want to add another draw to this line. Is an…

In Hong Kong for £35,000 with 18'000 miles in black and them nice red and grey cloth seats ? If you won the euro millions tonight would you buy it? https://www.pistonheads.com/buy/listing/11795536

Tues 27th on A22 heading north about 5 miles out of eastbourne

I used to use 15208-H8904 but these now seem to have stopped. Can't find any. The FAST supersession says 15208-53J00 which I think is also for SR20DET and quite a few Skylines. Amayama says 15208-H890C which I think is the same as the 15208-H8911 as used by the RB20DET, RB25DET and RB26DETT. Which is the right one? Ta. (BTW hallo all, hope you and yours are well. I'm still hiding away on the IoW ? )

When replacing broken part part on end of key barrel, you need to .. Take door card off Take two nuts off back of handle FROM outside you can now carefully pull handle bolts out Which are part of door handle. At this point you can see both wire rods leave on for now and rotate handle90 degrees or so You now can get at broken plastic part , take rod out of this one leave the other in place What looks like a rivet on end of key barrel is in fact a E CLIP Use small screwdriver and release this Take broken bit off and clean end of barrel put new metal type on and refit E CLIP Now refit rod and rotate handle back to original position m…

Its a stunner in red. https://carsandbids.com/auctions/Km1gBM0d/1991-nissan-300zx-twin-turbo?fbclid=IwAR3URZBBz06Di8uS0qyETqn9KCtxVCM-wqQL9yIm1EgTzV_hNb45__KGUMw

Currently up for auction in the US with bidding now at $25,000 with 6 days to run a very clean low mileage example. How high will bidding go? https://bringatrailer.com/listing/1990-nissan-300zx-twin-turbo-54/ Oh, and if that was my car and I saw how it had been lifted off the ground I would hit the roof!

A long shot but is there a common issue with the 300 that drains the battery? I'm sure it’s intermittent but didn’t think much about it as I put it down to a dodgy battery but fitted a new battery a month ago and had the kill switch turned off so all was fine. Yesterday I left the kill switch in at 8:30am and by 2am my alarm starts going off!! Couldn’t turn it off or open the doors so pulled the kill switch. I don’t want to be leaving it like this if it can drain a brand new battery in less than a day.

Hi all, as above I need the ABS ECU wiring loom schematic to enable me to identify each wheel sensor, my car is a 1993 TT, Can anybody help please. Thanks Sayers

Hi all i live in Horley Surrey and have had a white z32 tailgate stolen from near my car..It was ready to go on and was helping to hold down the car cover until i had a few days to get sorted.It is white and distinctive as where the rubber part with nissan and twin turbo decals go it was all flush.My neighbour apparently has the registration of van that was used to steal it and am waiting for him to get in touch before i waste my time calling the police,any other advice tracing this van when i get reg number would be appreciated cheers.

hi guys currently looking at a spring swap on my car, basically with the state of the roads where I live the ride is quite harsh with potholes etc. I'm currently running kyb excel g shocks and eibach springs, so considering going with oem springs. are tt/ na springs the same? my other option is swapping my wheels from 19's down to 18's

Dear knowledgeable ones, I need to replace my rear suspension and bought, what I thought was correct for the car, going by the registration number (Suspension part was KYB554104 KYB1). The garage told me that because the car was an import, the suspension I bought would not fit: it appears that imported ZX’s have different fittings from the British bought cars. I find this strange but it appears to be true. Can anyone offer advice, especially if you have had the same problem with an import? Perhaps there is a specialist I can go to.

which washer jets is that people use on the z? I did read on an old post they were Volvo jets but the link no longer works. need to replace mine as one side on each is blocked, tried various methods of cleaning but it's not clearing them.

Good luck England and bring it home.

On the birthday of the 300zx lets see your Z in a short description and picture. 1993 imported SWB 300zx TT manual.

Well after passing its mot a few days later my Z starts idling rough as if of a cylinder so after a few checks I think my front pasenger side (number 2) injector has failed after 28 years of spraying fuel. I did the screwdriver test and I can hear no pulsating tick from this injector so is that confirmed as my fault and if so where is the best place to get a new injector.. Did a vidio with the phone at the end of the screwdriver on number 1 cylinder then cylinder 2 hope its clear for you.