General Discussions - 300ZX Related

Hi guys, my zed is coming up for it's next service, is there anyone around the plymouth area who could do it, that i can trust!, while it's in for the service i need new pads all round too, this is the first service since i owned it should i do anything else apart from engine oil & filter?. Are these jobs i could do myself? im quiet handy with a spanner :smw: What i need to know is: what oil to use? what filters do i need? what brake pads to use?.. Also i have an idle problem, when coming upto a junction or a stop my revs will drop to 0-100 and then pop back upto 1000 rpm then the engine hunts half a dozen times before it settles down, sometimes …

Well she failed her MOT...for reasons below: 1. No rear fog light. I knew that but I suppose was hoping he would not notice as I have not had time to do it. 2. Some play in the rear suspension joint where it goes into the HICAS arms. 3. Emmissions...my CO was high. Limit is 3.5000 and mine was 4.953. Can anyone tell me why my CO is high? What would cause that? Is it that he just did not warm the car up properly as I still have the CAT on my car... Help on number 3 would be appreciated... Anyone know where I can get the bushes\joint for number 2? Cheers guys..

:confused: can any one please help, i posted a thread about my auto box, did the diagnostic and it throuh up a falt with the throttle sensor. ive since cleaned the sensor and connections but the probblem is still there, now when the revs hit 2000 they drop to 1500 and bounce back up and down, is this still the throttle sensor? :confused:

Does anyone have the link for AIV removal? The aussie link doesnt seem to be working. I know how to remove the buggers, just need to know how far back i can strip them and what/where to plug etc.. Cheers Scott

white 2+2 for sale outside the billingham arms pub billingham

I know some of you know i have a bit of a dillema with my engine at the mo.. anyway rather than get the big end bearing and crank replaced ive been looking into getting a recon engine in exchange instead.After all i dont know what other damage my Zeds motors got wrong with it.it had a rebuild under 30,000 miles back but has gone wrong again.Either the bearings were not replaced first time or somebody has treated it badly since the rebuild. Ive came across this company who have offered this service http://www.enginesdirect.com/index.shtml for a recon 300ZX TT engine for 1795.00 inc vat fitted.Obviously all the ancillaries will come from my engine but has a…

Just got an under drive pulley for zed. Would I need to change the belts or will the tensioner take up the slack properly. Also with the loss of the weight and balancing effect of the original pulley do I need to look at anything else while I'm messin with it? Cheers Marc

http://cgi.ebay.co.uk/NISSAN-300-ZX-T-TURBO-TWIN-INDUCTION-FILTERS_W0QQitemZ8029442912QQcategoryZ36680QQssPageNameZWDVWQQrdZ1QQcmdZViewItem

Hi all,I have been considering buying a 300zx for a while now and was looking at UK Autotrader site and saw this = http://http://atsearch.autotrader.co.uk/WWW/CARS_popup.asp?nU=0&make=NISSAN&model=300%20ZX&min_pr=75&max_pr=&postcode=SW19%203RQ&miles=40&max_records=50&modelexact=1&photo=1&start=1&distance=9&adcategory=CARS&channel=CARS&id=200602220888335 It looks like a really nice car,I tried ringing the numbers and cant get an answer.Im in Dublin/Ireland so dont want to travel without knowing the car is ok.Would anyone here be willing to have a look at it for me ? I know im new here and its a lot to ask but if I …

Guys attached are some scans I have just done from a killer find in the US. :shock: Turbo magazine to celebrate its 20th Anniversary have re-run its 1992 article on the bonneville record setting 300zx's :) The legendary 1991 Jun & Blitz cars. :bow: These were 800bhp+ monsters that show that even though skylines sometimes seem to have the edge on power, you cannot beat good aerodynamics from the off. Read the sidebars and imagine how sick the guy in the twin turbo ferrari testarossa special must have been to be toasted by our Japanese friends :tongue: !!! LOL Enjoy

This might me a strange one but can I ask who you would use and trust to do this in the midlands and why :(

my car has the usual nissan cranky 1st - 2nd gear change when cold (usual to me that is, the skyline was exactly the same).. may as well change the gearoil. and do the diff oil while i'm at it, so any recommendations welcome please guys... the skylines problem was sorted when i took it in to dixons nissan in hull, unfortunately they NEVER put the oil in i asked for, so i dont know what they DID put in, i changed the gear oil a couple of times after this and never did get it as good... what sort of capacity does the gearbox & diff take also, only if someone knows whos commenting on the above tho, coz i realise i'm been a lazy twat and could try a search …

Ok another prob with my Z!! Appears to b running very rich , above the exhaust the bumper is sooty black !! anyone know any common problems with them, sensor or something?? if give car a fairly good rev u can c the black haze from exhaust!! :( :( :( :( :( :(

I have an auto 300 and would like to no how complex a conversion to manual would be?? and what parts would i need to purchase

Help, my Z has started dripping at quite a fast rate my radiator coolant and water, I have taken some pictures below as it appears to be coming from some sort of metal tank beneath the engine where the cogs are?? Its not coming from either the radiator or the pipes by the looks of it, I have booked into a garage to get it sorted friday but I would like to know what you people think first. Any more questions about it please ask. It is leaking when the car is not running as well as when it is. All advice would be gratefully apprieciated. Many Thanks.

as above, approx value of front standard grey leather, drivers electric? seems to be quite a varied price in the for sale 'archives'!

has anybody produced any carbon fibre interior pieces - i.e boot floors, door cards etc for stripped out cars???

i had my worst fear confirmed by Gary at APT Tuning at Lenwade...... .the big ends are on the way out and will also require a new crank and has recommended a engine rebuild.Ive decided to stand by my Zed (in the hope i will have a strong engine at the end of this ordeal)but just waiting for him to price it up.Any body else know of any reputable Mechs in or around Norwich area who could tackle it?

hi im about to stick my dash down you no where it peels up from near the wind screen but i was wondering what type of glue i shuld use dont suppose the old no nails will work will it ? thanks

Can anyone tell me the size of stock front and rear brake discs please CheerZ Paul

People, after having a bit of a break in owing Z32's looking to retrun to the fold. However, bit out of touch with the market prices - so need a bit of guidance. There's a trader local to me who's got a '93 (L-Plate) 300zx Twin Turbo Manual (Jap Import, 90,000 kms, cloth interior, standard spec except for turbo timer/wheels), up for grabs and is asking £6495 (strikes me as being a bit OTT), but in reality is this a fair price, taking the wee or what? Any guidance/advice appreciated. :bow: PS.. Anyone (or know of anyone) interested in part-ex'ing/swapping against a non-turbo Supra? Needs to be a manual TT tho'

5-40w fully synthetic okay for a 300tt?

http://www.sureterm.com/sportscars.htm they've even got a pic of the Zed on the site :D

can anyone recommend anything to clean the crud off brake calipers? I've bought some 2nd hand and would like to clean them up before putting them on. Not fussed about having them painted or anyting, just cleaned up. ta

http://cgi.ebay.co.uk/90-96-NISSAN-300ZX-TURBO-STAINLESS-STEEL-DE-CAT-EXHAUST_W0QQitemZ8029787437QQcategoryZ38786QQrdZ1QQcmdZViewItem Anyone tried these? are they anything special?