General Discussions - 300ZX Related

Thinking of selling my 97 P SWB TT Hard-top manual with 15K on the clock. Anybody know the top price i could get for her.

hi chaps,anybody know if the zen garage are open,ive tried pms, phoning and no answer so left a message but nobody returns the call and then email direct to the zen garage but still no joy ,i only want to give them some work,but it seems very hard to even contact them has anyone else had this problem your comments would be much appriciated may somebody can tell me what to do next,cheers .IAN.

I know we saw each other as you waved, makes a pleasant change.

yes its another idle question.....(and i have used the search as well before asking this question) My Zed keeps running at 1000 in park (with air-con,heater etc off). Ive cleaned the temp sensor plug that was gunky reset the ECU and since then its idles cold at normal revs,then by the time temp guage reads quater of the way round it reads about 750-800 revs.Great i think!But by the car is back up to normal temp it runs at 1000 again.Ive cleaned the TPS connectors as well. Would this problem indicate the Temp sensor is at fault because it reads 750-800 with the needle a quater round?

Helloooooooooo Anyone know where you can get replacement plastic grill bits that sit underneath the windscreen wipers? I know concept Z perf do a trim kit but it doesn't include these bits! Ideas?

No3 cylinder :confused: If i remove coil conector no engine note change,(have tried other coil packs of Chunk(cheers mate)still same,so,having put in new plugs recently i took no3 out,was very white,but piston top not look dry more dampish,put another plug in,still same,so while engine running check spark from coil ,was ok(Chunk was witness :) ) so me thinks injector,just been to check it(screwdriver to ear etc)and its clicking away,if i take off injector conector it still clicks but lower note(unless i imagining things),car has new loom from ecu and series 2 PTU,any ideas or things to check further! i normaly have plenty patience but its bloody testing me and its s…

Hi people, I found out yesterday that I have slack in the UJ in the picture attached. How much would one of these cost and either get replaced or replace myself. Could there be anything else amiss ? Also, some time ago I replaced the shox with good stock second hand ones and now, after some time of them being fitted, I'm getting some clunking sounds from both sides but more on the drivers side. The sound is difficult to explain but it soulds like the thread of a bolt rubbing against some metal ! I have had a 'quick' visual inspection and all bolts/nuts appear tight. What I didn't do was refit the small orange gaskets on top of the front struts as they were both sh4gg…

Black G reg with black alloys, parked off London Road on Friday night (I'm assuming you live there because I've seen it a couple of times). At least, I think it's black, but I've only ever seen it at night so could be a very dark blue I suppose. Silver zed, went up High West Street and turned left at Top 'O Town roundabout. Saturday afternoon at around 3.30 or so.

Looked at online manual(AndyP site) according to that its pin out 103 for injector 3 on cyl 3,but i allso have another online manual(downloaded)that says pin out no 104 for inj 3,any one know for sure,as i just of out there in mo to find why cyl3 injec not firing. Tony

last night at the contra-flow road works on the M6 north bound modded black 300zx i passed it in my astra van and tooted. it was about 22.00 hrs

I am getting fed up with the goose honk from my recirc valves - but I don't want dump valves. Can you get uprated recircs - if so where from and how much ?

Has anybody got any pics of the standard Jap TT Valves. Im not sure if ones on mine are standard as i get a bit of a 'whoosh' when i lift off gas (auto)and they dont look anything like the standard re-circlics i had on the Skyline. Heres some pics of them.Sorry for the poor quality Any help greatfully recieved.

Hi ya guys can anybody tell me what the nissan uk part number is for the main beam relay and will it be different to the jap spec car as i have no main beam and believe this to be the problem. ive checked fuses,continuity etc all okay. the number on the relay in the car at the moment is 25230 c9911 according to nissan uk this isnt correct???? any ideas regards wade :tongue:

Could we have a sticky on this, as its always coming up. Just trying to help a friend insure his Zed, and am hitting brick walls on who will insure Zeds. So Ill make a start. Adrian Flux - http://www.Adrianflux.co.uk - 08000 83 88 33 Houghtons - Liverpool Victoria - http://www.LiverpoolVictoria.com - 0800 514 514 Carole Nash - http://www.CaroleNash.com - 0800 298 5555

Whos selling these now. Have looked on Mikes site (MJP) cant find them. Or am I going to have to get them from Courtesy Nissan. Regards Kevin

I am contemplating on taking my car mods to the next level. I have basic mods like, apexi indeuction kit, brembo discs, blue flame exhausts and a performance chip. I need advise on what stage to go next. I would like the Zed with a bit more power as at times I feel I miss my 928GTS performances. Any recommendations please with anticipated costs and where to get parts etc. Thanks.

Spotted you last night while walking down to the pub!!! You looked like you we're comming from the plan-an-gwarry area!!! Bet your another one from Cornwall who is not on here!!! :tongue:

A blue zed32. Parks in the residential building very close to wapping tube station. I go running and spied your zed through the security gates.

Would you be interested in this? Originally Posted by BanditUK Hi bud I'm trying to make a start on this whole welcome pack thing, had a chat with Andrew before, and we both agreed that the traders could do something like a discount voucher for 1st time purchasers and/or maybe even a little brochure or something, which would introduce the traders to new members, would be an incentive to joining members and would help pad out the Welcome Packs. I feel as this would bring traders extra business, that if they want something in the pack they would be responsible for supplying me with the vouchers/brochures (they get them made up at their cost) Obviously not a m…

tonight in asda carpark about 7:45 a really tidy black 2+2 tt i know it was you :tongue:

Yesterday evening, just before 5, going down into Dunkerton from the Bath direction. G reg with 99 spec front bumper and nice set of 18inch black rims on - looking and sounding good! Twere it you or someone else??!

for some reason i cant send pms or get them .mail box isnt there no more aswell. says you do not have permission to access this page. This could be due to one of several reasons: Your user account may not have sufficient privileges to access this page. Are you trying to edit someone else's post, access administrative features or some other privileged system? If you are trying to post, the administrator may have disabled your account, or it may be awaiting activation. any ideas????

Walking bac from the shop is saw what looked like a Std black 300zx. Emersons Green by Boots.

Was out in the zed and a 205 flashed,,,was it you???

Hi guys i noticed that a few of you have got polished/chromed plenums. i was thinking of getting this done, can anyone tell me how much this costs and where i can get it done. cheers for all your help guys :bow: :bow: :bow: