General Discussions - 300ZX Related

I have searched through previous threads without much luck. I have permenantly fixed in my boost gauge now and dont want to move it or play about with it again. Just to double check, can someone show me a pic of the pipe that the put their t-piece to take feed. TIA, Dave G

Obviously this will apply when fitting security systems to any car but USUALLY, what kind of immobiliser is the standard cat 1? Is it built into the key or is it a code you type in? Or something else? Cheers Al

I will be at crail on Sunday and I am going to give the car a go on the 1/4 for my first time. I have a couple of questions: 1. With the car being an auto, which is the best way to start off the line 2. Is there anything I can do to help the car go down the track, ie by driving. No losing weight jokes etc please :rolleyes: . TIA, Dave G

As i understand it jap fuel is 99RON, optimax is 97RON and premium unleaded is 95RON. As optimax is the closest you can get (without additive) to the jap fuel I always use it but I just put 30 quid in at 99.9p and it only took my fuel gauge to half! Also I just did a 150mph run up the dual carrage way so used most of it already! What are the conserquences on using 95RON unleaded in a j spec car? Anyone tried it? Will it overheat and explode?

How can I find out my paint code. Met black 1990 jap import. TT

Need to replace belt cos last one snapped, so loosend the 12mm tensioner locking bolt, loosend the 14mm bolt that you get to in between the holes in pulley, now what's left in order to move the pump so i can slip the belt on the pulley and bottom crank ?? cheers fellas smithy

SAW YOU LOL was heading towards bournemouth just about to go over the bridge bit.

I was watchin the clip from t.gear with the burn-out professors and noticed flames from the exhaust. What causes this and can it be created artificially ?

Looked like the one in your sig, I was in a red one flashing! :dance: If not who was it? :tongue:

I fancy getting one of those Carputers with the big screens like Legrath has. Any idea of costs please?

Anyone got any advice for restoring leather seats? The two front seats in my Zed have a certain amount of cracking in the normal places. There are no rips or severe wear. The back seats are mint, which is nice!! Thanks

Anyone got a clue where i can get one of these from? Failed its MOT on just this grrrrr :shock: Thanx guys Rich

Was talking to someone at work today who has a aftermarket dump valve and he says it reduces lag on the turbos? Is this correct for our cars?? or is he talking sh1te?

Would these fit? Front - 17 x 8 Rear - 17 x 9 Tires Front 235/45/17 Rear 255/40/17 Stud pattern 5x114.3

As suggested I tested the right hand side with Datascan, but got very different O2 result between the two sides, can someone advise which side is faulty? Right hand side At Idle sits at about 90, as the rpm is increased to 2000 it gently swings between 90 and 10 (about 1-2 seconds per oscillation), and continues to do so at a steady 2000rpm. Left hand side Sits at 35 at idle, as rpm is increased towards 2000 it dips slightly to about 32 and stays there, at 2000rpm it stays at 32, but when the throttle is released it slowly rises to 55 and then falls away to about 35 again. Would I be correct in assuming that the left hand side sensor is defective, as it…

This is on the front of my zx and I've never seen it in any pictures. Any clues? http://myspace-863.vo.llnwd.net/00674/36/87/674357863_m.jpg sorry I didn't put the picture in I'm not sure how to. Maybe someone else could do it in a message below. Al

Does anybody know if there is room under the bonnett to fit water to air intercoolers?

Today, at about 12pm'ish.

Hi all!! Thought this might help some fellow members, cause it has deffo sorted me out! :) Aon Classic Insurance Phone No.....01384455011, Smashed previous quotes by at least half eg; Mr Flux, Quote £1000.00 Mr Aon,Quote £459.00 :shock: Must have a second car tho and be over 25!

Anyone want my stock TT exhaust? it's pretty much the full thing, cats and all, with a hks superdragger at the rear. Only thing that's been done to it is the 2 wire things that go in to the cats were cut. It's in audenshaw (edge of manchester) and it needs to be collected soon. also got air con compressor and some random other bits. I think I've still got the stock rad (looking a bit rusty) and probably the auxilary fan (although I'll have to check it's still there).

hi all,i'm looking at buying new wheels but dont know if they'll fit.my car is a jap import 300tt which has been slightly lowered. the wheels are: Volk Racing TE37 RAYS PCD: 114.3 Front: 8.5J x 19 offset+29 TYRES : Bridgestone Potenza 235/35/ ZR 19 Rear: 9.5J x 19 offset+34 TYRES: Bridgestone Potenza 275/30 ZR 19 :confused:

Thought you guys might be interested in reading this. Been looking for stuff on the zx for a while now and have only just found this when I typed "300zx non turbo sound" into google :) http://www.mph-online.com/mag/rearview/009 Al

hi all, ive just got my new front bumper and was abit worried about wiring up the fog/side lights and the new style winkers, as ive got a uk car. does anybody know a DIY site that could shed some light on my situation? any feedbk would me muchos apreciated :) AD :rolleyes:

:)

Today while trolloping to work, I see a TT JDM zooming past me with 20 inch alloys. From an initial look, it seemed it had eibach springs and kybs. Just wanted to ask, how is this possible ? I thought the maximum u could fit was 19s. Any ideas folks ?