General Discussions - 300ZX Related

does anyone know why my thread where all i was asking for advice on my advert for my zed has been deleted i wasnt askin anyone on here to buy it only if they thought the ad looked ok because i think selling one of these cars is hardly the same as selling a ford escort so whoever it was nice one :mad:

......and you hate to see it! Drove to tesco to see how the car felt on the new rims when the offside started to knock :confused: turned around straight away and got back to the house to find i hadn't actually done up the wheel nuts past finger tight! :headvswal :wack: :o

Dear All, I am struggling to get the wheels I like in the correct size without a large wait. Can anyone tell me where I can find a good selection, that will fit the z, with tyres off the shelf? Anywhere in the uk will do however I am in the North west near Manchester Airport. Thanks. ps looking for 19's.

HI PEOPLE I NEED TO GET MY SPEEDO SET UP CORRECTLY TO READ THE RIGHT SPEED. :confused: I AM I RIGHT IN SAYING YOU SIMPLY NEED TO CHANGE THE "RESISTOR" OR SOMETHING LIKE THAT, ON THE REAR OF THE SPEEDO CLUSTER TO ACHIEVE THE CORRECT READING ON THE SPEEDO. :headvswal AGAIN, I THINK YOU CAN GET THESE "LITTLE CHAPPIES" FROM MAPLINS, OR A SIMILAR ELECTRICAL STORE. :D ANY HELP OR INFO IS VEY MUCH APPRECIATED. :bow: ALANZ

Think I found the leak LOL Right behind the passenger turbo :eek: Dunno why its so blurred but you can see the holes in the core plug at the top left corner and the rust running down below it... Cheers, Andy

Does the 300zx Club do anything at the NEC CLassic Show? Or has anyone here ever shown their car? I assume they rate as a classic?

My temp gauge has been a bit erratic since it's engine rebuild but has now stopped working completely, any suggestions chaps?

I'm looking to do a brake upgrade on my z32 . I currently have r33 Brembo front and rear but looking to get something a little more responsive. How difficult do you think it would be retro fit a set of Corvette Z06 Six Piston Calipers?? or a set of Porsche 928 Calipers

I think he mentioned the name "Mogs" and he lives in Hemel Hempstead, we had a little bit of fun in the tunnel... Does anyone know who this is?

Does anyone know if you can wire up the series 2 controls to a series 1 to allow manual selecton of screan, face, feet or any combination of as you can with the series 2

hi i have bought some down pipes and de cats off a friend for my twin turbo lwb and i have looked under the car and there are two silver wires and two littler pipes (like lamba sensers ) i think goin to the standard down pipes.. the decats dont have places for these to go to so what do i do with them? will i get any engine check lights on by removing the cats? cheers

would appreciate any advice you can help with, I get the dreaded vibration sometimes too, I have recently had my engine and box out to do my tubs, this only seems to have happened since i put it all back together, checked all the usual, exhaust rubbers etc. one thing occured to me tho, when i put back the bracket which holds the centre prop bearing back on the car, the bolt appeared to have a thick metal spacer between the bracket and the body at one side and not the other, I thought that does not look right so packed out the other side with washers untill they were level, could this be my problem? should it have a spacer (approx 1/4" thick) at one side and not the other?…

as above i just had my new auto box fitted it was fine before box went but now i have a really bad vibration coming from under the seat and glove box all through the bottom of the car can any one tell me what this could be and am i safe driving it while it is doing this cheers

Just got the zed taxed and tested today......woohoo... been off the road for 2 months now and its all good now that shes back up and running. A bit smoky for the first 15 or so miles but ok now. turned the boost down a bit as it was rippin the rears to bits. Gonna have the chip and apexi induction i promised myself from andy. i think it was a JWT or SE not sure but i,ll have to send him an email to find out. :hyper: ....happy days

lady driver on of the guys in work knows my car and saw yous going slow through speed camera then........... ????????

Hi I am going to be refurbing my engine hopefully with the help of Jimmer :bow: . I will be getting forged pistons, 555 injectors, maybe the z1 intercoolers. I am looking for somewhere in the region of 450-500 bhp (flywheel). What turbos would you guys recommend? I’m looking for something not to laggy low down and 5 bolt fitment for downpipes will not be a problem. I have been told Garret gt675rs BB turbos are a good choice are they any others and what benefits would I get from the different makes/models of turbo? Thanks

Hi all, Wot is the highest boost i can run on stock internals? Ive always run @15 psi before can i push her anymore? My spec list so far is: Dta ecu chip apexi avc r boost controller nismo 555's twin air filters fmic hard pipe kit + samcos custom made decat exhaust stage 2 t25 garrett 360 roller bearing turbos 20 psi max koyo ali rad x2 dump valves regards dan

Hello, was wondering what light could be shed on my issue. When i put my foot down a bit, the power light on the dash comes on. this i know is normal. however, the power light does not go out even after cruising at steady and low revs for quite some time. the only way to get it to turn off is to flip the switch next to the gear leaver to power mode, then back to the center position. It used to work normally. cheers.

Ok, I'm almost at the point of having to make a decision on a clutch... not least cos I'm gonna have to get the money together for it! I've gone with Greddy 16g's (and a rebuilt engine etc etc) & am looking to be making 500+ bhp, with maybe the potential to go a bit further in the future... so, what clutches can people recommend?? Obviously RPS are the clutch of choice, will they handle the power/ torque?? Anyone got any experience of Carbonetics? OS Gikken also seem to have a good rep too.. Not got a budget in mind (as is apparent from the above!) but I want to get it right first time! The car's a play thing - trackdays and weekends only, so not TOO b…

Just wondering what use to make of this useless area on my dash? The 2 drawers are too small for a CD disc and the drink holder doesn't. Suggestions please - what have YOU done with yours? I suppose I am looking for pics or graphics of what's been done. I can think of a few things - just looking to see what's been done to best effect.

Hey, My left Pod which controls the fan and cabin temprature etc. isn't working but the wiper control on it is. The pod on the right works fine. It lights up but non of the buttons respond and it doesn't display any numbers in the lil display.

got my eye on the 13inch disc brake upgrade from z1 motorsports, seems quite decent and the pound is very strong at the minute has anybody else fitted this to their car?

Given Nissan cut costs on my 95tt by not putting the boost gauge on the dash clocks why would they bother with the following: Weird huh? I was certain that the sensors were located at the back of the engine bay by the brake fluid reservoir.

Keighley Trade Sports & Performance ? They have a very nice 300zxtt in stock just now :) Thanks ;)

Hi Guys I have searched and searchedand looked at the workshop manual but cannot figure out where the time control unit is, this controls the interior light fade time when you close the door etc... Cheers Graham