General Discussions - 300ZX Related

is best to use for a service :) thanks

I am getting the occasional light smoking from what i think is the ns exhaust though it may be both, when I see the smoke, I try to detect it and it disappears. I have been advised to leave it on the forum, enjoy the car basically, but I would like to know the cost of replacing the turbo oils seals????Anybody down south that can do it. ???

Having replaced my seats with leather, I liked the look of the perforated leather centres and decided to get rid of the suede interior pieces I fitted a few years ago. I took off the suede and covered the panels with the same perforated leather that is used in the seats. I was fortunate to be able to contact the manufacturer and have them send me the same leather. Went from this To this

Hi, Just been reading through a lot of HID related threads and I must admit I'm thoroughly confused as far as terminology is concerned. Could somebody please explain what is meant by dipped beam, main beam, high beam etc. in relation to the following: 1. The main lights when driving at night; 2. The traditional 'side' lights (not always on the side these days); 3. The very high intensity beam (blue symbol) when driving on a dark country lane. Also, how do the above relate to the round and rectangular lights on a Z32. Thanks.

member syko has an exhaust for sale but i cant contact him as Ive not subscribed yet, could someone give him my phone number or tell me how i could contact him please as i really need the exhaust thanks

I have just had a moment of madness and bought a set of Cobra Misano's. Problem is i haven't thought about fitting issues until having a quick search through the forum! Anyway, i am now aware that i will need to do something to the subframe to fit them. I have a spare set of electric seats and wondered how easy it would be to remove the subframes from them and get them fitted to the new seats? Is it a relatively straight forward job for an engineering company to make the necessary modifications or will i need specific subframes?

oh needs to change the bulbs which are situated in the bumper but cant seem to find how to get to them, is there an easy way or does he have to take the bumper off? please help he's doing my head in lol

just to clear something up are all the wiper blades on the zed 21" as i need to get some now ones , and best recomended please, i have searched but not 100%

Anyone know where I can purchase one? I have looked on the Z centre site and can't find what I am looking for.. Any help appreciated! Thanks.

My car is a series 1, I have read a little info with regards to changes from the model years, and I have been wondering if Series 2 dash pods would be compatible with series 1 wiring e.t.c The reason I ask is due to the airflow direction option and apparently the settings stay stored when you turn the engine off/on, unlike the series 1. Can anyone tell me any info on this please. OR if it is possible to make a series 1 store which settings you had the heater/fan settings on. Thanks! :)

after my new zed starting to run on 5 cylinders, today i changed the plugs, hoping this would cure the problem. just got done, and now it's running on 4 cylinders:cry::cry: now to try and find some replacement coil packs:cry:

Hi all, Got my car up on stands & the wheel off to see if there's anything amiss with the suspension as there's a loud creaking noise when I go over a bump in the road, however, as nothing's hanging off or obviously broken/snapped I have no idea what could be causing it. Could anyone suggest which bits I should be checking or what I should be looking for? There's another issue in another thread I started which means I may also need to check the engine mounts. Could these be the cause of the creaking? Again, how to I check these? Sorry if I seem dense, but I have very little mechanical knowledge when it comes to cars. Cheers, Brian

Ok once again my car is back on my drive on axle stands seems to be something that happens weekly. This time i have a knocking noise from my engine. Quick histroy with this i upped the boost preasure too 15psi. I took it for a spin and ohh man it was great. I pulled up in a bus stop and notice a slight noise turned engine off and on and it was gone. I started the drive back home and the noise was getting worse, pulled up again and its coming from the right side of the engine. I looked at the oil preasure gauge and its at 0 then it went back up slightly and it dosnt get passed the first positive line, even when driving. Any ideas here guys i really cant afford a …

Hey peeps, Anyone got any info on these?? http://cgi.ebay.co.uk/NISSAN-300ZX-Z32-5X114-3MM-20mm-ALLOY-WHEEL-SPACERS_W0QQitemZ350251467443QQcmdZViewItemQQptZLH_DefaultDomain_3?hash=item518c9d42b3

Hi all, anybody know where the relay for the fule pump is on my N/A? most of the writing is wiped off. . . well it is 18 yrs old.

Hi everyone. Need a little advice on the best way of fitting an engine and wiring harness. I've almost finished building my TT engine and is getting ready for dropping in the hole. I was wondering if it's easier to fit the new harness to the car or engine first? The inside of the car is completely stripped so there's no heater matrix or dashboard in the way. Any help is greatly appreciated. Stuart

I have an intermitent issue where the electric fan kicks in and i get check engine light. Car then runs badly. Fanalo come son just with ignition on an and not with engine running. I have taken off temp sensor and cleaned it up and car runs ok but problem does return eventually. Have used a connector cleaner this morning and it doesn't come onon ignition. To check it i disconnected temp sensor and put ignition on and the fan doesn't kick in.... so now i have no idea what's going on ! Any idea ?

A really excellent step by step guide to fabricating with fibreglass I found today which i thought i'd share with you whether it be for sub enclosures like this guide or body panels: http://forums.nicoclub.com/zerothread/362362-how-to-fiberglass-fabrication

im just gauging intrest in the sale of my beloved zed :cry: as you know i have had her for about 8 years now and have spared no expense at all on keeping it in pristine condition, uk spec 1990 with the manual conversion full engine rebuild from phil c&s wood with new tubs complete bare shell strip down no rust at all paul bailey bodykit with blended skirts polished plennum apexi, gtr disks, traction controll, ice install infinity kappa, jl sub radius r6 alloys 18"

yesterday(saturday) 2:30pm junction 23 anti-clockwise nice car had oval exhausts and 300zx in gold lettering on rear screen

Few things in here i didnt know. Safety better than the 350Z and the Awards :cool: Production 1989–2000 Body style(s) 2-door convertible 3-door hatchback Engine(s) 3.0 L VG30DE V6 3.0 L VG30DETT V6 Wheelbase 2450 mm (96.5 in) 2 seater 2570 mm (101.2 in) 2+2 Length 4305 mm (169.5 in) 2 seater 4520 mm (178 in) 2+2 Width 1790 mm (70.5 in) 2 seater 1800 mm (70.9 in) 2+2 Height 1245 mm (49.0 in) 2 seater, standard) 1250 mm (49.2 in) 2 seater, T-bar roof 1255 mm (49.4 in) 2+2 Curb weight 1610 kg (3550 lb) 2+2 1496 kg (3300 lb) 2 seater weight varies with performance package In 1989 Nissan replaced the Z31 chassis with th…

I know this has been listed before. but i have only ever seen one pic of this mess. There are many more here :rofl: http://carscoop.blogspot.com/2009/04/made-in-china-nissan-300zx-lamborghini.html

Hi, Just thought I would post this as it has been a bit of a pain to get the right fittings together. basically I wanted to convert the fuel supply and return lines to AN fittings so that my entire fuel set up is solid. The fiittings I used (and there may be others) are an 5/16" to -5JIC hardline connector, which then accepts -8JIC x 1/2"UNF adapter - looks like this: And bunged to keep the crap out... It was only about £13.00 for all of the above. ;) Hop ethis helps someone else save some time and money ;-))

In the BIG nissan book it says at the FPR is should be 43.4 psi But reading back on other threads they say its lower? So what should the pressure read on idle?

anyone know of an idiots guide(pref with pics) to removing and replacing speedo cluster as I'll be doing mine shortly from jdm to uk clocks cheers in advance