General Discussions - 300ZX Related

red zed heading down orton road carlisle at 10.30am this morning. i was in mine and waved but just got blanked :cry: also...silver zed heading towards keswick (lake district) 1pm ish again i waved and nothing back!!

Hi all, Very strange.... when driving normally, there's been no problem(autobox), however when leaving the car on idle for about 5 minutes or more the exhaust starts bellowing out smoke. :( Any ideas? Could this be a turbo seal going or something much worse? (my motor has covered about 75k...) Of course I'll be getting it checked out shortly but wondered if anyone else had this happen? :rolleyes: cheers, Quadsmarty!

Well this bloody Z is starting to take the mick Windows working fine yesterday got in it today (very hot day) and my window would not go down? Any ideas, I cant see it being the switch and I doubt there is a fuse per window? It makes a very quiet clicking noise when you press the button but that could be the motor or the button lol

Where is this in the engine bay, I want to remove the hose from the solenoid to check if it's working at all, but have no idea where it is. Ta.

I'm fitting my profec b 2 boost controller and have hit a snagg.Am i right in saying i connect to the "com" and "No" ports.The problem is i also have an "NC" port, do i plug this?There is no plug supplied with the kit and only 2 connectors.Thanks in advance. P.S. i'm using the Dab-1 quick guide if that helps you see what i'm doing.http://www.300zx.co.uk/forums/showthread.php?t=73132

Was travelling along the A46 dual carriageway and got the chance to power away and a large plume of smoke came out the back end, 'Oh, dear!' I thought, 'I may have blown a turbo!' So kept the speed down, and didn't notice any problems with the engine in any way, so when i got to my destination I left her running and checked all round her. No oil leaks, no smell of burning oil from either zorst, but there was smoke coming from underneath her! Anyway, that was the other week, I've had her up on ramps since then and, although we could see signs of oil, couldn't see anywhere that it might be coming from! But it is defo landing on the Cats, hence the burning. Did the same …

started to clean all connections...and the injector connections (2 prong) are covered in the green corrosive stuff..is it me or do you have to take all the vacuum pipes etc to get at the connector on the passenger side nearest top? any other way of doing it? thanks

just going over the car now (long story but it hasnt been running properley for a while...ie runs mega rough and has no power to drive) and im cleaning all the connectors...this one is really dirty plus the wires are split...what is it for? (will do diagnostic check once battery is charged) car is tt manual thanks for any help

I need your help guys and gals. I started exploring Dare Alloys and Azevs however the waiting times are a bit long as I need a full set sooner than later. However, can you all give me some steer and recommend alloys with a fair bit of deep dish with 5 or even 6 spoke design. I am hoping for 19 inches. Ok, before everyone recommends Racing Hart and the exotics beyond my financial means, I was hoping for to buy them with a budget of about £1500 with tyres, ie. poor man's alloys range. Any ideas and recommendations and also a supplier would be extremely grateful. Thanks...

saw a red Zed near the magic roundabout in hemel... was it you?

Hi ,can anyone help me ? will a gearbox from a 300zx non turbo auto 1991 import fit on a 1991 import tt auto? are they the same box and will it be a straight forward transfer? any help would be greatly appreciated thanks kev.

as above, mot time soon and my fooking handbrake has to be lifted nearly all the way to the top to even slightly work, can i adjust it from inside the car, anyone get any fotos?

What a bugger those recircs are to get at and get off! does anyone know whether if you disconnect the vacum you can just leave them on. Not sure whether it will block the holes or whether it will leave them open? Any ideas?

hi guys.any advise on the anti-lock brake light.i turn on engine it goes out then after about a minuit it goes on,the fluid is high and the pad are good ?

Hello I have a z31 1989 3.0 i V6 turbo which does not boost. The engine does all the work. Can't work out why, the boost gauge moves etc and I can hear the turbo whistle up but no power comes from it. Also there seems to be a samll miss on the ngine like one cylinder is not running fully. Could some body also confirm where the oil pressure should be because currently it is below 30 when warm and does not rise when the car is throttled. Its my first z car and has never boosted at all. The car doesnt smoke or burn oil. It currently feels like its only running 110 bhp which is slightly disheartning. Can some one help?????? Shab :xxx: :cry:

Last weekend I finally managed to get the gearbox back in after replaceing my clutch with a OS Giken one. Due to me having little time to work on car I now have to put everything else back in position, but now have a stoopid problem - the clutch fork is stuck in the backwards (free) postion, I cannot even get the hydrolic cylinder back in position its that far back. If I try lever the fork backwards (towards the rear of car) it just bends? whats going on :wack: lol. anyone know! cheers

hi ive done a search but cant find the answer to my question do the HID kits replace the high beam or the main beam? im pretty satisfied with the high beam as it is and just want the mains to be brighter. also are the jap TT's H1 or H1c lamps, i can never remember, im not at home just now so i cant check either. would be greatful if you could help me out so i can buy them tonight. Cheers, Fraser

Hi guys, ive been thinking about getting a grounding kit but what id really like to know is what advantages do they give? Ive read on afew websites that they can give upto a max of 8bhp, but that was on a subaru wrx. The reason why im after one is because everytime we get in / out of the car we get an electric shock. Would a grounding kit eliminate this? Ive also read that this improves engine response, smooth idling and an improvement on fuel econemy. Does a grounding kit really do all this? Whats peoples thoughts on these as i know alot of you have them? Many thanks. Rob

How many people have had to replace their tubs due to fitting decats?

lights been flashing for a bit, so i got some dexron stuff, just dont know where i put it. Can someone tell me where it goes or put a pic up? Thanx

Hey guys I have an HKS BOV on my 91 Auto Twin Turbo. I just noticed today it was not making any noise. Any ideas on why this would happen. I have tried revving the engine in park and letting off the accelorator and still no noise. I have been driving it and given it some foot and let off and no noise. Any ideas on what would make it stop working.

Hi, I had a clifford alarm fitted last week and the fitter removed the drivers side A pillar to fit the alarm's antenna. This A Pillar has my Defi guages on it and now the A Pillar is hanging down as the clips are not clipping back into place. The clips dont look broken, ive tried to bend them out a little bit but they are not clipping in. Do these clips clip into anything special or just the hole in the pillar? I might need some new clips, does anyone have any? Colin

I was under the bonnet today and came accross 2 empty plug sockets near the hicas gear. I was wondering what are these for? and should there be anything conected to them (if anything)? If there should be something connected to either of them, can this cause any problems? I dont supose this has anything to do with the car being a manual does it as our auto zed has both of these connected to something? Any help is much appreciated as usual :D See attached piccys.

coming out of Mc donalds car park on the coldra roundabout about 12 oclock with targas of ??i was in the white van going passed.

Can anyone tell me what position the pcv hose goes that links the plenum to the passenger side outer rocker cover. What I mean is that there is a small penny washer inside the hose that sits about 40 mm from one end of the hose, does that go against the plenum or at the rocker cover side. Cheers John Crisp