General Discussions - 300ZX Related

Ok i sent a couple of pm's out earlier with the possibility of postponing because of the weather, but i guess most people are out on Saturday night and won't recieve them.So we''ll steam ahead and meet up tomorrow at 1 o'clock at the beehive as planned. Let's just hope the rain eases if even for 30 minutes or so.....

Can anybody shed any light where this pipe goes to, or comes from ?? 89, T/T, Pipe comes from a small actuator type thingy up in the drivers side, rear of the engine bay, near the bulklhead. When engine is switched off it hisses for a good 5 secs and then dies. Engine appears to be a little uneven as well, connected ?? Gave the engine bay a wee clean up, so would assume I knocked it off perhaps. Alan...............

today about 4:30pm i think heard you before i saw it :cool: - nice clean spoilerless Zed along the carlisle parade. J

Think it might have been dgsignmaker I was parked on my brothers drive, just past the Burn Hotel, on the way to Hetton, when you drove by with a car full.

I am looking at the Demon Tweeks Anti-Roll Bars and they only come in a 27mm front adjustable not 32mm which I was looking for would there be much of a difference between the two sizes as far as road holding?? Or would the 27mm be fine? Cheers http://www.demon-tweeks.co.uk/products/ProductDetail.asp?cls=MSPORT&pcode=WHIBDF1

My Z will not go into extended boost 9.5psi It stay it standard boost 7psi Temp plug replaced , ecu code 55 cant find any obvious leaks.. My viscous fan is always on, i believe this to be normal But it idles at 900/1000rpm which seems high to me? :confused: what should it idle at ? Has anyone got a pic of the BSCV connections, i believe mine 2b connected, will be nice 2c im looking in the right place ..... ;) Im stuck guys any advice welcome

Just found this and thought some of you might be interested

At about 11 this morning on the A10 near Ely.

Only had a zed now for about 3 months and its my first, needless to say the car has me hooked, anyways i really want to start chasing big horsepower, so ive been puting the building blocks in place ie.. just making sure the car runs perfect as it should, right so i think forging the engine would be a good move yes, so what size piston do i need to get??? will it be relative to any liner wear i have??? or will 87.5 be the one to go for??? Cheers guys

Have a good day bud. ;) :duffer: :duffer:

Been trying to contact this guy for the last couple of days but hes not answering, He txt me yesterday saying he couldnt speak asked what I wanted then said he would contact me later. as of yet he hasnt, is there another number for him other than his mobile? Thanx in advance

just been watching best of top gear on UKTV G2 and it was sowing the one where hamser and may were rider mopeds then taxi-ing people home in their own cars and i nticed that hamster tried to race a zed away the some trafic lights ha ha ha :hyper: :slap:

Wow I can think of a million different things i can do with a slim line tv like that. SONY OLED

I've got one of SE's HICAS eliminators to fit but there's a nut missing and after lots of searching I've worked out it's an M12 x1mm thread but I can't find one anywhere :confused: Found a few with a larger/coarser thread but not 1mm. Anyone got one knocking about?

Can anyone tell me what the scoop is with 265mm tyres on the rear of the 300zx? My one has ( i think) standard UK spec 16" alloys that are onlt 245mm wide, can i fit 265mm wheels straight on and is any modifiction required? Andy

Hi I have just purchased some ProSport gauges from SWZ. They are boost gauge, oil pressure, and water temperature. Do I need to get any other parts for the fitting. The instructions mention that there are additional parts available for the oil pressure and water temp gauge. (a sandwich plate I believe?) I presume these are to help with the fitting. Can the gauges be fitted without these parts, or is it recommended to get the other bits. If so, can anyone recommend a site to buy these from? And the car has a remote oil filter kit fitted. Will this cause any problems? Lastly, with the boost gauge, will having a boost controller already fitted cause any …

Hi, Anyone got any ideas why the standard brakes on my TT make quite a load clicking noise when the break pedel is pressed? Its coming from the front calipers (both sides). Nissan looked at them and said they are working fine but could not find what was causing it, NISSAN are a waste of space! Would be grateful for some help....... Paul

Or has anyone got the installation manual for a Clifford Matrix?-I've found a wire and need to know where it belongs!, Cheers. ;)

To my GF :D Soon as i find a Zed TT :) Its a lovely car but I want somthing faster, Hence the TT

Fitting an after market air filter, amongst other things, and was wondering what to do with the oval pipes in the pics ?? Leave them, remove them blank them off, or what ?? Its the 2 pipes, oval in shape that feed the airfilter box. Last pic was the end of play this evening !! ;) Alan............

Just been out for a blast in 'The Black pearl' and it didn't break!! :shock: (I'm touching wood whilst typing!) :D

:cry: i'M in shock still ,,,just found out my mate is dead.....//. I have been trying to get hold of him today after speaking to him yesterday finally got hold of his mum who says they have found him dead in his garage,.. don't know the circumstance yet............I,m gutted he was a top guy and my best friend i'll miss him dearly .....my condolenses to his family & girlfriend Zena who are totally distraught . rest in peace jay dude you will never be forgotten by me and a lot of your friends. :cry: :shock: :shock: :cry:

Whats the bore standard size of the vg30dett & what are the oversizes available? ;) (Can't find my datasheet) Rebore Prices Apprx?? ;)

Seen a few times parked next to Kwik Fit in roker :cool:

As above really what do you guys think. Not looking for massive increase over the 350 bhp i am running now poss 400ish! So are they worth a look or need to be avoided??? Dave