General Discussions - 300ZX Related

http://cgi.ebay.co.uk/ws/eBayISAPI.dll?ViewItem&rd=1&item=290192877618&ssPageName=STRK:MEWN:IT&ih=019 can anyone tell me anything about this? any experience with it? i've just bought it and was wondering if it was any good :D

hi, my bmc leaks. i need the 4 gaskets of the pistons. where can i get them? regards florian

Hi folks, I've just had a wee service on my car and found out that my air filter was clogged badly and my air flow sensor connections were corroding. This is a K & N system, so i need to replace the air filter as it's beyond repair and to replace the sensor. I've been using more fuel than is normal and been told this could be the reason for it. Where is the best place to get a new filter and air sensor.

Hi ya can anyone help me? I have an auto tt but whenever I accelerate hard the trottle sticks open for a little while not much fun when i wanna slow down. does anyone know what this could be?

Does this look bent to you? hmmmmmmmm

Yesterday afternoon? I passed you near Focus!

Seen a Silver zed on the a1 at the Tranent-Prestonpans fly-over this afternoon just before 2pm. Think it was 90-94 by the look of the spoiler! Anyone from here?

Which model of Z is this balance bar from ? :confused: just one pipe on the o/s

For some reason my stock boost gauge has stopped working, it just sits to the far left (as it does when ignition is off) on -7. I have an after market boost gauge which is working fine - shows good vacuum on idle and boost under load. There doesn't appear to be any pipes hanging off that I can see anywhere. Any ideas? Is the stock gauge electrical or mechanical? Cheers

an know?

I was just reading the Z1 site about their long blocks and they say that having a dented sump can cause oil starvation as there is only a small gap between the bottom of the sump and the oil pickup, especially bad if there is a dent in that area. My engine seems fine and pulled good figures on the dyno. Should I be changing the sump? Where abouts is the oil pickup?

Happy Birthday Crotchrocket/Annihilate & JaffaZ32 :duffer:

Since putting new engine in, and new ptu, TT now ticks over perfect, adjusted idle and all is good. But. When stationary under no load , engine revs lovley, but turbos dont go (i think) as boost gauge stays at 0. Have cleaned every connector in engine bay and all are working, when driving it wont go over 3000rpm so i guess safe mode. Have replaced temp sensor and it works 100% When i killed the last engine the drivers side of engine was were the leak was and i guess water got into exhaust pipe. Ive established that the cat was blocked so its now gone, the passengers side is great and when reving it has lots of pressure. Problems are: 1. Have done ecu…

I have been on V-power for quite a while now (right from when it was call Optimax) but after the last refill it did seems not quite right, infact when I check my exhaust, there are quite a residue of black smoke on my otherwise clean tail pipe. Could be just bad fuel, perhaps plugs..? I'm tempted to put in Tesco's 99 Octane. What do you folks reckon? thanks

What happens if your car's on 18s and you get a puncture and have to fit that space saving spare? Surely it's smaller (diameter) than the other wheels. Does this cause a problem?

I'm trying to keep my tt stock, or close to. So, as it says :p , where should i go, for the best prices?

Heading southbound around midday sat 5th. Only got to see the roof and hi rise spoiler as i was on opposite side of road.

Hello I'm new here to the forums. Was advised by a friend to post here as I'm having serious trouble with my car and am looking for some advice. Someone replaced the power steering belt for me, and afterwards the car would not start :( There is no compression when trying to start the car. Diagnostic test says the coolant sensor and ignition primary are at fault, though the mechanic said it may be the timing due to the lack of compression. I'm absolutely baffled by this, as the car was running perfectly before the new belt was fitted. I live in Sheffield, so if anyone could offer advice or knows of a good garage/mechanic in Sheffield who could help, ple…

ive looked at the front of my car and deceided i want a new look but dont want fibre glass so excluding the 99 look what other options are there in polyeurothene??? ;) i know theres a bumper thread going on at the moment but ime just intrested in eurothene options

hi peeps spent ages today trying to fit my bomex mirrors which are electric the mirrors came with a connector block on them but once i'd taken my old mirrors off the blocks were different , then i noticed the colours of the wires matched so i removed both connector blocks and hard wired the wires together the result was the mirror wont adjust with the switch and now the passenger mirror which was folded back before i started doing all this wont fold out does the drivers mirror also have something to do with the passenger mirror as the wires on the bomex mirror were 3 different blues ( blue/black blue/red and i think blue/green ) and the 2 green wires arent connected t…

How much do you all reckon you should spend on wanting a 500bhp, good handling show quality zx??

The previous owner said that he had the cam belt changed and all the seal etc etc. so why would there still be an oil leak from the front pulleys? I dont want to have a mechanic take everything apart just to find that its not the problem, then have to pay more to find the leak? whats the cause of oil leaking here as ive just spent hours reading up on previous threads with the same problem. im also getting oil leaking onto the nearside turbo causing it to smoke a little under the bonnet??? could the leak from the cam travel this far as the oil could splatter off the fan belts etc?

A gunmetal grey z driving away from tesco about 19:30. Nice :cool:

Can someone steer me in the right direction for this job? I also have an oil leak which seems to be coming from the cam belt pulleys etc so that will also need investigating. whats a good price for this job?

im in north london, anyone know where the closest RR is for me? I remember someone saying they payed 70 quid for a dyno? Want them to check a few things while their at it like datascan and cas timing. I will replace my mbc with 1mm mig tips before i get there.