General Discussions - 300ZX Related

Anybody ever seen this before ? My painter showed me the rear bumper to what looks like heat bumps and advised to change it out for a smoother one if I can find it. Looks as if the shape of the rear end has went wonky in the sun at some point.

so this morning i decided to tidy up my boot build, i've never been happy with the position of the amp and never really got round to relocating it, so it's now under the boot floor i'm still not sure if i'm going to keep the sub or find something smaller like the slimline subs. and same same with the carputer project great bit of kit but still not sure if i'm going to keep it or move back to a single or double din unit. i do need to either replace or make new boot floor panels as the old ones are a little past their best. so i've gone from this to this (yes i know it needs to be hoovered)

How To Make Your Car's Face Pretty Again http://thegarage.jalopnik.com/how-to-make-your-cars-face-pretty-again-1794126301

The parking aid on the front bumper can you buy these new? I know someone who's looking for a replacement.

n/a i think, getting a wash and polish by the look of it as we went by on the bikes this morning

Ummm...think someone needs to pull out the little book from oxford and see what the definition is; http://m.ebay.co.uk/itm/1992-NISSAN-300ZX-TWIN-TURBO-FAIRLADY-TARGA-/122427858025?hash=item1c8144dc69%3Ag%3A98sAAOSwmgJY4QBL&_trkparms=pageci%253A2cfcf07c-1bc9-11e7-8863-74dbd1805f6a%257Cparentrq%253A49e8e52215b0a6a8d0d18164fffec609%257Ciid%253A5

Hi Gents, I need to replace the rear track rod ends. is there a kit out there that removes these ? My Hicas has been locked out with a brace so no need for a true track rod end. It failed on this Nearside Rear Outer Suspension arm has excessive play in a track control arm inner bush bush in hub Any help would be greatly appreciated. Cheers, Adam

Was looking at the official dealer japanese catalog today when I grabbed one in Okinawa and I´m a bit confused. Was there an option on the 98-2000 models where you could choose the veige leather seats with red stitth in them? or did I dreamed that.. I think I saw this somewhere years back.

Hi as anyone got any pictures of the elbows I just bought some not received them yet but from the pictures they both look different were they bolt up to the turbo one looks like four bolt hole an the other looks like six thanks stephen

Hi guys ;) I have a yellow z32 TT (1991) And currently rebuilding engine... And now i have new headache, what collor shoud i paint block and heads..... Any suggestions? How you done yours? Thanks

hi guys bit of a quick one my number plate bracket has been attacked by tin termites and is falling apart as i want to eep an original one on there, is the JDM & U.S version of this part the same? part number 96212-30P00 also does the front bumper need to come off to fit it?

hi Guys, im fixing a crack on my bumper and have done the fibre glass on the back but was wondering what type of filler to use on the front, as well as on other defects (now i've cleaned off the non hardened plastic filler.) The reason i ask is that while sanding back, the existing filler used on top of the grp/gelcoat whatever you call it, resembles the std filler used on solid structures, P38/Upol/bondo etc. i mean the plastic filler is pricey and the P38 type is not. Opinions please.

Hi all, About 6 months ago i bought a second hand race logic traction control system and i am looking to get it installed/install it. The harness appears to be in good condition, with minimal cutting in its removal by the previous owner bar a few wires, and a full write up is available on how to install the unit but the only issue i have is not being 100% sure that the harness is as it should be and with my lack of electrical knowledge i thus would not want to self-install without assurance it is all as it should be and then can follow the guide easily.. Ive tried to find complete wiring diagrams to follow to make sure everything is as should be but cannot find mu…

Who's successfully re-trimmed their interior rear quarter panels (the upper parts that go saggy)? I'm looking to do mine and took it to my local trim shop as I figured they'd be able to match the vinyl and fit it correctly with heat and the correct adhesive. Alas, no, they advised that the material and manufacture technique would mean that they'd not be able to get the right match or fitment and showed me some swatches. The stuff they use is proper seat vinyl which is about half a MM thick and would not cover correctly and the grain wouldn't match nor the colour. Has anyone successfully done this? Mine need doing, they're not terrible, but they're not great. I w…

Hello good people of the 300zx forum I am in need of replacing the nock sensor, I have taken out the fuel injectors and under that is a block held down by 6 bolts however 2 of the bolts are hidden behind a steel pipe which I have no idea where it leads to so I'm asking does anyone know? Pictures are

Hi, can anyone tell me which fuel line i need to tap into in order to provide fuel to the Petrol Solenoid side of my Nitrous install please. Better still if anyone has a piccy , I would be very grateful. I do have an adjustable fuel pressure regulator fitted, Thanks Sayers

Hi all, Have a coolant leak behind engine. I can see where its from, its from a 1/4 inch metal pipe that goes through a 90 degree bend and joins a 1/2 inch metal pipe. Its underneath the two electrical connectors that unclip, about 5 inches below. Theres a pin hole right on the 90 degree elbow. Didnt leak to start with, but had idling on the drive for 10 minutes, switched it off and water was spurting out. I can see on the 1/4 inch side it goes into a rubber hose, so thats easy to come off. However the 1/2 inch pipe dissapears, one side to behind drivers side head, the other side disapears down towards the ground. Question I have is how easy is it to rep…

Hi guys, I'm just looking for a Z specialist on the south coast near to Bognor Regis. Need a Cambelt doing next monthish as I have no idea when it was last changed and one of the idler tensioners are failing. Cheers in advance Edd Sent from my iPhone using Tapatalk

I have my old purple painted rocker covers from my previous build which I was planning on doing a transplant onto the new engine. However not wanting to taint the new engine I was thinking of stripping and using the covers that came with the engine. One of the things that came up is to blast them or not as I've been told that the inner baffles can get the sand in them and its hard to get out. The previous zed was done like this but I don't want this new engine busted too. I have the blasting cabinet in my yard and its easy enough to use but should I ? I've could also blast it with soda but that's expensive and can take three times as long. …

Could please change my winter works thread title; http://www.300zx.co.uk/forums/showthread.php?186561-2017-Winter-Works To "Project Dittohead Red" Cheers

Hi Guys Anyone running waterless coolant ? My thoughts are no pressure from hot water/steam but are are there any downsides to it ? Tony

Just like to say thanks to Ian greenfield for sorting out my last pieces of trim for my zed,two perfectly good targa tops:) aufuwl drive up to littlebouough...50 mph most of the way..hate the motorways:(,again thanks Ian top bloke, and a fair price for them aswel,although it cost me more in fuel at 18mpg...lol,and to top it of just as good jestuere he gave me this for my impul:) thanks Ian your a star buddy.....

Hello. Trying to track down the cure for a rattle type of noise that tends to be when cold and low revs. Cambelt, pulleys done 2 years ago at Eurospec. When I first heard the noise, I thought it was a small exhaust blow but it's not that. Eurospec have stripped the front and had another good look at pulleys, timing belt, tensioners etc and they're fine. They suspect the VVT solenoids or gears. A bit of research leads to this https://z32.wikispaces.com/Variable+Timing+Control#Function-ECU Control-Non-Turbo which seems to point to the gears (if it happens when cold, the solenoids wouldn't need to operate anyway). Has anyone had this issue and if so, what was the cure? …

Unique Paypal reference :- Receipt number: 1LY23964M9892963T Cheers Sayers

Sorry if i have posted in the wrong section But im desperately Looking for a rear drivers side inner wing Ive scoured ebay but there the same breakers all the time And have no inner wings Ive searched google and cant find a breaker with a zx Does anyone know of a breaker anywhere that has a few zeds or Know of anyone breaking one