MarkDerby

wow thats quit an old way of boosting low output stereos it uses the Hi speaker output .. Kinda crapy really

MRX F30 4-Channel £175 quid m8 .. typo on last price 4-channel car amplifier 50 watts RMS x 4 at 4 ohms (75 watts RMS x 4 at 2 ohms) 150 watts RMS x 2 in bridged mode (4-ohm stable in bridged mode) CEA-2006 compliant Variable high- and low-pass filters (50-400 Hz, 12 dB/octave) Variable bass boost (0-12 dB at 50 Hz) on rear channels Preamp and speaker-level inputs Class-D amplifier design MOSFET power and output stages Fuse rating: 25A x 2 8-gauge power and ground leads recommended - wiring and hardware not included with amplifier 9-15/16"W x 2-5/16"H x 9-1/16"D

yeah its 200w RMS over 4ch ... So u gonna get a true 50w per speaker .. Unlike your 18w now

i can get a alpine mini amp thats around 200w over 4ch .. RMS but u be looking around £230

what he said ... but use a Hard flat block ... Plenty of water and a little rubbing soap

dont get me wrong any after market coil overs is going to be a firmer ride ... but its not a go kart thats for sure .. i used to have some tein ones .. well they was more suited to race track the minsters are really nice

Minster-r's coil overs .. adjusting Camber arms ..

They are Axe CS Lites

tbh et40 on 9.5" wheel is spot on thats all most level with the arch

go to a Model Shop and Ask for Trim Line Tape ... £5.50 for 5m Roll and has all colors and sizes i used to sell the stuff ..

hdmi lead .. other than that plug it all in and play

30mins >1hr ... taking it verrrrrrrrrryyyyyy easy lol

there only $450 there abouts so betime u get them here with dutys/vat/post conversion 400quid ... dont think its silly on the cost tbh your gonna end up paying 250>350 for 2nd hand ones

Just like to Say Have a Happy Christmas and a good 2014 :) From and Me and the Team @ Automodz Mark

Concept Z performance .. m8

jack up wheel off pull back the arch liner and undo the bottom bumper crap tray ... u can get to the bolts

Ok Jecs Brand are ok and do make 90% of the injectors on the market Inc Nismo ones Denso plugs are the type u have now .. standardization type for many more if there the ones on CPZ site .. Nothing wrong with them at all

Best place is CPZ or Z1 .. if you buy early type then your rail will be fine .. expect to pay around 400ish for New Budget type .. up to 1k for Branded

na its just you lol

Most of use just remove it .. and Feed a drain line from the rad down to the floor .. there are some that say its needed .. and some will say its not ... for reasons if thats what i want to do then just do it

Nice pic .. and one of my ICE builds on show too :)

Chris ... there is a little Problem m8 as the Original holes are 6" .. most after market Speakers like the ones i sell are 6.5" so u have 3 options Make the Holes slightly bigger .. Make new Speaker Door mount plates .. or Buy a set of me Nice door pods to stick on your door cards Check here http://www.300zx.co.uk/forums/showthread.php?166475-Custom-6-5-quot-Speaker-Door-Pods Standard System Setup 6" Fronts 5x4 Rear Bose System Setup 6.5" Fronts and Rears

no its not that changing the rear end .. its replacing the bushings with in the sub frame that he wants doing

oh my very nice :)

just to be safe keep an eye on that ... all so just check your Rad water is not Oil stained as well