General Discussions - 300ZX Related

I am in the middle of putting some new springs on the rear of the Z and have just discovered the strange loose feeling is due to the fact that the rear shocker is broke. Does anyone out there have a pair of standard rear dampers I can lay my hands on for a reasonable sum? Cheers Ivan

hi bought my first 300 tt 2+2 a while ago not much done to it apart from a new front bumper fron the Z centre had been fittted (ZC002A) the thing is it scrapes everything fitted new front dampers but it didnt seem to help much. Looked at a lot of zeds and they seeem to ride a lot higher than mine any help would be great. p.s 18" rims fitted

Have the old Z problem of my drivers doorlock spinning without opening the door, I know this is a broken link and I need to remove the outside door handle, but my question is can I remove this handle (two nuts) without pulling all the window gear out and the glass, which looks a nightmare.

Enfield Town today. :dance:

As above if anyone can Emai me a copy. As I've now run my car in and because I put a new loom on I need the diagram to plumb into thr ECU wiring. ASAP please.

im after a boost controller set my heart on the profec B anyway do u guys use any thing else? ie those controllers for the fuel and air? sorry to sound vague :rofl: :rofl: do they work well together?

Hi, i just bought a red 300zx, so i'm new around here and i thinking of of starting to make some modifications and i need to know how much hp a stock bottom end can handle? Thanks Sergio

Hi there all zx forum members i need some expert advice as you probably know im new to the zed experience and have bought a 300zx tt it had all sorts of problemswhich have been resolved by way of totally rebuilding the engine.now my worry is with the turbos..........I want to replace them with stock turbos but the prices are sky high it seems that i have to look for alternativr turbos. on the American ebay ive seen some t28 tubs off a nissan skyline (a distant cousin of the zx twice detached). What would be your advice? (i) will the turbos be too powerful for an unmodified engine albeit rebuilt. (ii) will I have probs fitting them? (iii) is there an alternative (iv)…

engine rattles when started in the morning from cold for about 5 seconds then sounds sweet as a nut. Obviously the oil getting round but does it mean my oil is too thick? or something else?

Are you on here bud?

Anybody recognise Champions C109 as a valid fit for my 300ZXTT ??????????????? I had to choose this filter without the benefit of a definite reference ...it has Nissan on the box. Old filter on the right new on the left..no really :p Everything seems to line up except those holes are farther out..does it matter.

sumone emailed me from this site a few weeks ago about a FREE conzult check where can i get this done?

hi guys just pricing up mods for my Zed, want to get rid of the standard spoiler and go for the perspex skin also want side skirts and new rear bumper, also a respray, Ive been advised to get all this done together??, can anyone give me a rough cost for it all please? Ref the respray I would like it to stay red so is this cheaper or round about the same? thanks Lee

Dark grey, smooth rear in Camberley about 19.10 tonight. Did not flash cos i was in my metro

Hi all Still have a rattle from the front of the engine when cold. Turn the engine off then back on and the rattles gone! Anyone had anything similar?

noticed sometimes my boost level pulse at at the top end when accelerating hard, doesnt do it all the time though. would a boost leak cause this? Its only hapends when controller turned upto 1 bar. Boost only hits 0.9bar though and saftey is set at 1.1bar.

My car has gone fookin kookoo! I was driving home from Falkirk last night at around 12.30 and the car started seriously spluttering and hesitating. This has happened once or twice in the past. A couple of times i have just stopped the car, started it again and all is hunky dorey. Last time however, it wouldnt run until i had cleaned all connectors, sensors reset ECU etc.. anyway, i pulled up hoping it would be ok when i re started it but nope! It kept spluttering, revs dropped and it cut out. Engine light flashing on and off. Car would not go above 2000rpm. I tried a good few times but no improvement. I gave some of the connectors a wiggle but that was all i cou…

Past you about 10ish last night near the big retail park in the centre. (sorry, dont know falkirk too well).

My Z'ds going to the bodyshop in a few weeks and i'm thinking of getting rid of the standard boot spoiler as it's looking tatty, i like the look of the Z'ds without any boot spoiler. Has anyone done this mod, if so, what do i need to finish the job. Someone said i'd need a perspex strip to go on top of the tail lights? I need to know what's needed so that i've got everything ready for the bodyshop.

ive checked tps with a multimeter it was readin 0.48 ive now adjusted it to 0.45 ive also dissconected battery (to reset ecu) have i done this right and would running tps at 0.48 make a difference with the running of my engine the probs i was having was overfuel consumptoin, stalling on pulling away randomly backfiring (only slighty though) throughout the rev range when driving ive also changed the maf (which i did before resetting the tps) which didnt seem to make much of a difference only made it feel a little more responsive and wasted a tenners worth of fuel in 19 miles so am i on the right tracks so far checking the tps and resetting ecu …

Looks like it is coming from the water pump, does this mean the water pump needs replacing? The alternator belt slipped and pulled at a funny angle on the pulley wheel attached to the pump and then the leak started.

If i junk the cruise and hicas systems, what other things would i need to consider? looking at ripping out both and adding hicas eliminator - will i need to block anything off at pas pump? having a "plan to ditch it" day today! :dance: will it affect any other systems? just about to do another search so may answer my own questions in a minute anyway! :smash:

hi A newbie here hoping to join the ZX club. I'm planning on looking at a car, the seller has said that the steering sometimes goes stiff and heavy. Would this be the steering pump or sensor fault? Also, what's the likely wallet damage on this? ta for any help.

I'm looking at changing my brake discs, pads and lines soon. Been looking on ebay, and have come up with a few options, all of which from the US. They all claim to be Brembo, they are all standard size discs (rotors :rolleyes: ). And they all seem to offer the options of plain, cross-drilled, grooved or drilled and grooved, normally done in-house on a standard Brembo disc. So what do you think, are they worth it? Or is it a case of some cheap disc, in a printed 'Brembo' box? Would 'Brembo' be stamped into the disc? TIA Whoops, LINK!!!!!

would putting a j spec maf on my uk zed be ok as a replacement thanx in advance