General Discussions - 300ZX Related
Z related topics and discussions
79,672 topics in this forum
-
Hello , My current tyre sizes are 225/45/17 frnt , 245/40/17 on the rear... Just bought some 18 inch RX-8 alloys they fit with spacers, what size tyre does peeps recommend on these ? i think theyre 7.5 or 8 J width i will update later ... Any help appreciated ! Thanks
-
Yesturday I took my zed tt on a 300 mile round trip and found out it seems to have an electrical problem around 80+ mph the door light on the dash flickers and so does the interior light at the same time I can hear a clicking of a relay on the pasenger side rear also the hicas light came on which made the steering heavy which now works after switching engine off and on again, the millage counter stopped working but thats not just it on the way back the engine started to splutter not much but enough to wind me up! that went after a mile and came back later then went again and now my clifford alarm has stopped chirping to but still works with out the siren but that also com…
-
- 6 replies
- 349 views
-
-
-
went to swz performance yesterday and they sorted my zed out so no longer in safety mode!!! now im looking to do a few performance mods induction chip and boost jets are all these safe to do or am i just asking for trouble? car is completely standard but well looked after anyone got any disaster stories or does everyone run these mods with no probs????
-
- 16 replies
- 606 views
-
-
i noticed a problem with my cruise control light yesterday. I pushed the master switch a the first green light came on, i set my speed with the stearing wheel buttons and the second green light came on on the left of the wheel panel. when it was reset when pushin the brake extra the second light went off but when resumed or set at a different speed the second green light would come back on. i tried to reset the system by turning off the master switch and turning it back on again but it seems to be on or off when it feels like it. any advice guys?
-
- 4 replies
- 398 views
-
-
hi guys, i need a bit of advice, firstly, I have to option of acquiring either r34 or r33 GTR Brembo calipers, is there any difference in performance between the two? if there is no performance difference between the two, which is easier to fit? from what i have read so far, the r34 brembos need the mounting holes drilled out, but are r33 calipers a direct bolt on? do rear brembo calipers fit the stock zed rear discs? are they too a straight swap? if i get upgraded brake hoses too, do i buy 300zx ones or skyline ones or are they both the same? (sorry to sound thick) I will need to buy discs and pads too, which ones are best? thanks!
-
- 10 replies
- 1k views
-
-
I've had two Zed's since June this year but, despite searching long and hard, I have been unable to find where Nissan have hidden the cup holders! Come on someone, put me out of my misery, where the hell are they? ;) Dave
-
- 2 replies
- 263 views
-
-
I know it's been done may times, but who are you with? I am currently with Carole Nash, the Chaucer Classic policy last year was £275 FC for up to 5000 miles pa. Their renewal has come in at £375 - quite an increase. I have just called Adrian Flux and Houghtons this morning. The same (Chaucer) policy with them was £420 and £637 respectively....... What's going on :confused: I'm 36 with a clean licence and have only had 1 claim in 19 years :rant: Richard :smw:
-
- 10 replies
- 491 views
-
-
The 2007 Calendars will be ready to post out next weekend. :hyper: :hyper: Sorry to pester everyone but we need payment to the club account and address (to Steve-300ZX) ASAP. Would prefer to get them posted all at once. If any member or registered user wants a calendar but hasn't yet added there name to the list, please do so, ASAP, to ensure you don't miss out. Add your name to the folowing list: http://www.300zx.co.uk/forums/showthread.php?t=82549 The quality of the 2007 calendar is first class. I guarantee, you won't be disappointed.
-
- 0 replies
- 281 views
-
-
JUST GOT HOME FROM REMOVING MY ENGINE THIS EVENING!! :nana2: spoke to my local very good nissan dealer (unusual i know) about supplying det sensor and was quoted 175 for it! :confused: is this right, if so is there anywhere cheaper to buy proper one? also they are having a problem finding wiring loom to sensor on micro-fiche, does anyone have part no for loom and approx price?? what torque setting should sensor bolt be as i understand too tight or loose will cause sensor to read wrong?? regards steven
-
- 10 replies
- 511 views
-
-
I was wondering if any one wold like to share thier nitrous 1/4 mile times im interested in puting nos in my zed but whanna see how much faster it makes the z
-
- 20 replies
- 901 views
-
-
hello. Is fitting a short shifter an easy job or hard??? is it a job i can do from the top of the car (cockpit) or do i need to work from underneath it? Does anyone have any links for a site that explains it or anyone possibly done it before? Cheers.
-
- 4 replies
- 338 views
-
-
hi can anyone tell me if you can fit a universal induction filter to a zed? or am i better off gettin one that is designed to fit?
-
Today i was driving my Zed and all of a sudden my Hicas,Light's came on and will not go off. My battery light is partily Illuminated and the stock boost gauge is sticking at -7 even if you boot it?? My aftermarket boost gauge is working fine and shows no probs. I have checked all my lights and they are fine! The alternator is charging ok with 13.9 volts at idle. My Hicas fluid is at full . Fuses are ok and earthing points are ok as well as battery connections :confused: Found this post above but was never solved from what i could see or the resulting problem was not posted.. Any Idea's????? :confused: i Have searched for the same problem i have and only f…
-
- 1 reply
- 444 views
-
-
For sale in QD. Not only the full kit which comes with three washes worth of shampoo and filter... It also comes with a full size filter and bottle of shampoo too - both good for another ten washes. All for a tenner! If I was skint / had more time I'd buy loads and sell the full kits and shampoo/filters seperately on eBay. edit - maybe I could hawk them out of the back of the auld Datsun at shows?
-
- 3 replies
- 409 views
-
-
I am about to have my knackered PAS pump replaced, is trhere anything else I will need apart from the pump? such as gaskets, belt etc.? Scotty
-
Hi, Just finished cleaning/repairing/replacing/re-fitting the AII/Air Reg etc, and now she starts like new and runs like Paula Radcliffe however... Now I can't get my keys outta my ignition as that little black button solenoid thingy is not doing it's stuff!!! Could I have disturbed something whilst in the general area of the engine bay that would cause this to happen (connection etc) or is this a complete co-incidence do we think. Car has been laid-up for 4 weeks prior to today's burst of activity so... As ever your guidance appreciated - couldn't find nowt via the search! Cheers AndyGP
-
- 3 replies
- 305 views
-
-
anyone ?????? :nono:
-
- 5 replies
- 579 views
-
-
Hi, I paid by bank transere Tues or Wed this week, but I have not yet been re activated. Funds should be there by now, have sent an email. Can anyone speed this up please? Cheers.
-
- 0 replies
- 311 views
-
-
HI PEEPS,GOT A FEW QUESTIONS,AT SOME POINT WILL NEED TO REPLACE MY TUBS ON MY JAP AUTO!!!!!,AFTER MUCH READING UP ON THIS EXCELLENT FORUM,NOW NO MY TUBS ARE SMALLER THAN THE JAP MANUAL TUBS,REASON BEING THAT U GET LESS LAG AND THEY SPOOL UP QUICKER,SO WHAT TUBS DO I REPLACE THEM WITH???????????,DONT WANT MONSTER ONES,DONT WANT TO PUT STOCK TUBS BAK ON,BUT MAYBE CAN U PUT THE BIGGER JAP MANUAL TUBS ON,NO IT SOUNDS DOUBLE DUTCH BUT AM AT A LOSS NO,ING WHAT TO DO,ALSO PCV VALVES,HOW MUCH WOOD A GOOD GARAGE CHARGE TO FIT THEM,NO THERE A KIN PAIN HA HA,MANY THANKS IN ADVANCE :confused:
-
- 1 reply
- 308 views
-
-
just wanna tell everyone about si,s 500bhp monster zed looks amazing just seen for the first time today watchin the lads at swz performance gettin it runnin cant wait to see it on the road and a big thanx to swz for sortin out my zed cheers
-
Hi there When I disconnect the yellow connector of the valve, my car just dies out. Tried to raise revs by turning the screw on the valve but to no avail. Anyone got any ideas??
-
Happy Birthday Greg All the best mate. Make sure Ryan gives you a chilled out day :D