olly300zx

http://www.sxoc.com !

Third dabs please ! If the others don't want it I will ? Olly.

Sweet fa mate, send your details over and I'll bung a copy in the post ! Olly.

I've got around 1000 applications including , movie software to turn it into a video camera, games, wallpapers, screensavers etc on one cd you can have, if ya get one, best phone I've ever owned ! Olly.

I didn't bother as the one supplied with the kit is a pile of dog sh*t and caused me to spend hours under there trying to get the box in ! In the end I used a ratchet end and my eye to line it up and the gearbox slipped straight on ! Olly.

Usually depends on the amp, I have a kenwood 823 and that will run two 4ohm subs in parallel to give one 2 ohms connected to the bridged output so it can be done, but sometimes it causes the thermal protection circuit to switch it off. Bloody loud though ! Olly.

After not driving mine for a few weeks it did this and now after a few days it has cleared up and I put it down to not being run for a while and the tappets pumping up with oil ! See how it is after a few runs. Olly.

No I haven't !!! you will have to use this address as I'm not subscribed yet ! Will be soon though moderators ! oliver.hayes@ftsbonded.com Olly.

I would use a 2 x 90w rms amp and turn the gain down, that way you aren't pushing the speakers and the amp has plenty left should you upgrade later, and you will !!! Olly.

I've got one in Silver, just needs a spray to gray if your'e interested ? Let me know. oliver.hayes@ftsbonded.com Olly.

A lot of the 200sx boys do this as did I with mine, now I have a 300zx I was thinking of doing the same !!! They use Rover 800 fans which are twin slim ones and then dump the viscous one ! You have a lot more control over them then as well ! Olly.

Its not just the processor thats extra, the memory is ddr, better, the hard disk is 80gb, 20gb bigger = more storage. The screen is 15" TFT so very flat and easy to put somewhere. The dvd drive is a re-writable one so you can write DVD's and have a lot more storage on them ! Don't worry about an on-board graphics card, it just means its already built in, not ideal but it is 64mb which is fine and you can upgrade later and turn it off ! I do agree with the others though that Packard Bells can be a nightmare !!! BE WARNED. Olly.

Well I've got Avon ZZ3's on the front of mine and if you can get them to understeer or squeal, your a better man than me, they grip extremely well. I lost the back end with pirelli's on but the front helped me to correct things because they didn't skid so much ! I haven't tried anything else on the front so can't compare but I wouldn't say they are bad ! Olly.

I have never heard of a Rusty Zed and mine doesn't have a spot of it anywhere, even though it is 12 years old, with original paint ! Olly.

Robtor you are so right ! I am still having knightmares now ! Snapped 3 studs myself as well ! ooh the drilling lol ! Its just not that easy to do trust me ! Olly.

The ptu would as you get no spark when the engine is being cranked !

one word "PTU" Clean the ptu connectors and make sure the connector is on tight ! Olly.

Everything is helpful !!! The problem is once its up and close to going in and I feel up the centre it just doesn't go high enough for the spline to go into the centre it just touches the bottom of the centre hole. Did any of you remove the rear cradle (dunno what its called black metal bar that screws into rubber mount where gearstick sits) or not ? Olly.

It doesn't go high enough with the tunnel in the way and when you get it closer to the engine, you can jack it up a little more but there isn't any room to line it up straight and then just push it needs to go forward and up at the same time, I'm having no luck. By the way did u get me cheque matey ? Olly.

I don't have to move the engine do I ? as it came out in the position its in and if anything the engine has dropped further towards the rear of the car making it a little easier but it just won't have it ! I can't seem to get it high enough and forward enough to clear the transmission tunnel properly and get it over the top of the flywheel with the spline in the centre. Is there anyway of making more room or something I haven't removed which I need to ??? Olly.

Anyone know how the hell you get the manual gearbox back on ??? I have tried everything, going in at an angle, straight, I just can't seem to get it to go onto the spline no matter what ! Any ideas peeps as its now doing my head in ! p.s. I have 12 stitches due to it falling of the jack and slicing my hand up ! B**TARD BOX. OLLY.

you wont need to put on reflectors as the reflectors are on the outside and the clear lenses go on the inside so you would have clear lenses plus the original reflectors on the outside ! OLLY.

If you could scan the instructions in that would be a great help as I've yet to fit mine and only have the Jap instructions ! Thanks Olly.

Yes Ammar it was me and now I have got it up to scratch its awesome and really looks the part ! Nothing major has gone wrong with it apart from the clutch and it has never failed me once, had it for nearly a year now ! I am in no way saying don't buy it but GET IT CHECKED OUT by someone in the know ! Nothing can be guaranteed even if its brand new, but I think being as old as it is certain parts if not replaced will be worn, suspension, bushes etc. Have a look at a few other Zeds of that age as well to give you a comparison and look at what other zed's of that price range are available, year, model and spec. Olly.

My fav is the thrid from last pic right at the back is a silver one with the widest of wide arch kits on it, looks awesome ! It does work but you have to wait a little while, unless you get the red box placemakers, then it won't work and your firewall is probably stopping them coming through ! Olly.