Going to start this thread for members to post up what they did each day to there zed. I will start with getting my MOT this morning. So what did you do today on your 300?:cool3:

Had a day of successes and of slight failures... :rofl:

 

Started by adding a hydraulic strut onto the bonnet and deleting the cruise control...

 

 

Last few days i've been rewiring in all the speakers, fronts went in fine, rears i'd bought some bose dynamatted boxes and some infinity kappa components and crossovers. nice speakers for what i wanted it for.

 

Slightly too large for the holes so next job is dremel the holes in place then fab in some new covers to make it nice and neat...

 

Fitted new track rods and track rod ends, get the tracking set and drove the bloody thing!

I finally fitted my radio/cd blue tooth ect.

Dials fitted two weeks ago

Art213

In a bid to avoid having the dirtiest scruffiest Z32 at Coventry I washed, mopped and polished mine today.

I am also at Donington circuit this weekend for a Nissan event so it was time to have a banner erecting trial too !!!

 

 

[ATTACH=CONFIG]80684[/ATTACH][ATTACH=CONFIG]80685[/ATTACH]

 

Don't worry Slick Pete, I am taking mine.

It's a mixture of primer and gloss, looks great from about 20 feet but up close it is a bit of a dog. Lol

Don't worry Slick Pete, I am taking mine.

It's a mixture of primer and gloss, looks great from about 20 feet but up close it is a bit of a dog. Lol

 

Still? :lol:

 

Cant wait for tomorrow when my braided clutch hose arrives... I can finally complete my manual conversion and get the car down for MOT!

 

and even better news to me is that my backordered rear wheels are arriving into the country this week, I wont get the car 'finished' for the conventry meet but it'll sure look different at JAE! :yes:

Still? :lol:

 

Cant wait for tomorrow when my braided clutch hose arrives... I can finally complete my manual conversion and get the car down for MOT!

 

and even better news to me is that my backordered rear wheels are arriving into the country this week, I wont get the car 'finished' for the conventry meet but it'll sure look different at JAE! :yes:

 

Ouch!! :lol::lol:

Went down and did some photo of the car until a seagull sha- over it nice

Outsides clean now, just the interior and engine bay to go.

Had me wheels powder coated.

 

 

^^ Nice!

Agreed very nice, they would look great on my car. Hand them over lol.

Very very nice buddy :hyper:

Thanks guys :). They couldn't get the azev center caps off without breaking them. So I'm thinking of getting some Z center caps. Any idea where's best? EBay?

Thanks guys :). They couldn't get the azev center caps off without breaking them. So I'm thinking of getting some Z center caps. Any idea where's best? EBay?

 

There is a few on ebay if they fit mate

 

http://www.ebay.co.uk/sch/i.html?_trksid=p2047675.m570.l1313.TR0.TRC0.H0.Xazev+centre+caps&_nkw=azev+centre+caps&_sacat=0&_from=R40

Thanks guys :). They couldn't get the azev center caps off without breaking them. So I'm thinking of getting some Z center caps. Any idea where's best? EBay?

 

Surely they're moulded centre caps? I'd say you'll need originals to replace them.

Had me wheels powder coated.

 

 

Great wheels! Fantastic fit for the Zed too, regretted selling those straight away!

Stuck on mate with some high bond stuff. Even with a heat gun. Got them off but two are badly chipped. Think il will get some Z stainless ones. The only Downside today is that the bloody security nut has worn and I can't get the stocks off!! Grrr

Surely they're moulded centre caps? I'd say you'll need originals to replace them.

They are molded, contoured with the spokes. Azev would probably still sell them.

Sticky pads.

Firstly took this...

 

Used a pipe cutter and flaring tool to do this...

 

Then tidied up the wires temporarily till I get more time to extend and route them inside the wing...

Then the lovely other half polished up the leather and interior for me :)

Then I realigned the HIDs for the first time since I got the car and can finally see further than 2 foot in front of the bonnet...

 

 

Now bed! :)

Prep almost completed!

It's going to be pushing it to get that thing back together for Saturday morning buddy!