taff

tescos super or any make super :duffer:

you can grab the bar on these and pull backwards and forwards and the top plates flex.STAY AWAY. :duffer:

thanks for pics mate been searching the net for hours days trying to find a pic cheers taff.

z32 stud pattern is 5x114.3 centre bore is 66.1 Centre bore can be larger but a spacer ring is required but not smaller. offset i think 38 or 40 .I have few freinds who drift and they go on about gay offset wheels 35+ to 50+ because they tuck under arches to much . The wheels on the back of my z are 9" wide with a 35 offset and 20 mm hub centric bolt on spacer that makes them a +15 offset .Front are 8" wide with a 25 mm bolt on spacer that makes them a +10 offset.Some cars can run - Offset eg - 15 TO -70 but wheels but will need flares or pulled and rolled arches .I like the drift look with wheels flush with arches .plus a wider track is good.Lower the offset the more they stick out also clearing front caliper alot more for bigger calipers . im sure a 300zx will take a zero offset 8 " wheel on the front without hitting the front arch.

Still going to fit it as its got 3 sensors tapped into filter housing for oil temp/pressure gauges and its cheaper than and a greddy sandwich plate one of the main reasons for buying it .Easy to fit gauge sensors and remove filter.And it looks nice and stays clean with a greddy filter attached.A lot of race cars use these 1 ease of change 2 on a lowered cars can save engine if filter is hit from underneath.

I want to fit under bonnet it can be done .also last filter i took off was mega tight and a pain to get to 1 hour job. this kit cost me £60 brand new on ebay and is good quality trust product.I think i can shift batt over and fitt on inner wing so nobodys seen one under bonnet.

Ive just got a grex trust oil filter relocation kit .But stuggleing to find space under bonnet to fit has anybody seen one fitted to a z or got one fitted .thanks taff :duffer: :duffer: :duffer:

HKS timer fits in place of clock as well type o and type 1.

Just brought a recaro sr recliner and need a subframe as i dont want to mess around fitting to standard rails.Does anyone know how can get one off these im having problems finding one thanks taff.

Try the red fuseable link under bonnet near brake servo .

Hi mate bushes from demon tweeks not alot cant remeber how much i brought them for my s13 there the same fitment as s13/s14\r32/r33\r34\z32\ easy job just undo all four subframe nuts one at a time and fit between big domed washer and subframe.Hold subframe to body nice tight.Im also fitting 6 rear hub bushes 2 in the rear hubs both sides and 2 in both the short link arms .Not going to bother with rear upper arm bushes im going to replace with ajustable cusco ones .see you at the next meet mate might go to santapod . :dance:

If the bushes arnt to shagged you can use whiteline subframe locking pineapples .Just fitted them to mine my bushes were ok just done it to tighten up the rear.half hour job.Ive removed all four bushes before on a s13 200sx same subframe and its a nightmare \hammer \blowtorch\ chisel \drill .

6:15 yesterday with body kit looked very nice with private plate.

Congratulations mate have a good day.

small black plastic cover near servo push in type fuse with clear cover on top red one is stop lights then 5 green ones cant remember what there for . :hyper:

thanks guys :hyper:

fuseable link maybe.worth checking theres one for stop lamps.

PCD 5X114.3 centre bore 66.1. offset i think 40 or less lower offset the further the wheel will stick out of the arch.low offset is good might need to roll arch though. :hyper:

Thanks for info mate im not looking forward to this job though.slicktop all one bit. :headvswal

Has anyone removed the trims along the roof and screen on a swb slicktop .Mine have chrome showing through .I want to remove sand and spray these black again this is all one bit and i think will bend easy .New there £70 a side .thanks taff :hyper:

And gto i hope :hyper:

Just wonderd if anyone knows how many uk cars were sold through nissan dealers .Im told 1000 uk supras were sold in 4 years at toyota dealers was there more 300s sold.Colchester nissan dealer had a red auto demo. :hyper: thanks taff

Try redline mt 90 might work .Mine still crunches but at higher revs than before .Made gearbox slightly noisey all gears though.4 bottles.

redline mt 90 expensive though .Demon tweeks sell this £17 a bottle [QUART] .You will need 4 bottles to fill as gearbox capacity is 3.1 litres.You will also need a syringe to pump in as redline oil has no tube on the bottle its a pain in the arse.Also a good oil is silkolene full synthetic. see oilman do a search.

Cheers mate discs are on nice one.YELLOW SWB TT SLICKTOP.