ScabbyZ32

Can sell you a conzult/Blazt cable for cheap which will help? :)

I had similar and it was knock sensor issue. Sorted it with the 1000ohm resistor mod untill i replaced sensor.

Hi - Sorry I did miss your post. The indicators have been sold with the bumper, sorry.

link goes in roundabouts??

Not sure I want to sell to a non Member Lol. Will give you a bell tomorrow.

Cheers for answering folk in my absense m8 :)

Sold mate.

No probs bud - Might be a bit later when you get a reply as I need to drive to dundee for bits for my scoob now. Ahh cars cars cars! :rockon:

Lo Rod, Sorry have been working away the past month and a bit, but am now back home. Unfortunately i have the crap tweed interior, however, the dash pods all worked as expected, if I remember correctly they can change illumination colour too depending on your mood (last owner modified them). Not quite sure what the pods are worth - offers? - To compliment, my dash gauges/speedo have the silver dressing kit on them if you want them too, again offers? Cheers, -Stu -Stu

Cheers bud. 95% of car still available.

Hi All, Turns out the floor on my Z has turned to cheese while its been parked up (it was garaged for most of it!) Therefor just so you know all parts are available. Please post here if interested - I will be renewing my subscripton today in order to advertise car in parts for sale section, as well as get PM's enabled again. Cheers, Stu.

Anything in the rules against me renewing membership in order to advertise my poor Z as breaking for spares, as the floor has turned to cheese. Please advise, Cheers, -Stu.

Hi Guys, Long time no post - Poor Z has been sitting in the garage for a year feeling sorry for its self, so have decided to put it back on the road (I will renew membership as and when it is) Anyways.... The reason it was put off the road was it constantly popped water hoses, as soon as one was fixed another would go, therefor ive been following the aus300zx guide on doing the plenum pull. I have gone over the removal guide a good 6 or 7 times but I still cannot get the plenum to lift off - its wiggling but will not lift - anyone got any ideas? Thanks in advance, -Stu

New nickelback album doesnt seem to be cutting it for me....but after a listen on myspace this does! Put me down for a copy too pls. Cheers, -Stu

Maybe a bad earth somewhere causing it. Ah the joy of Jap cars lol :)

i'm not a Z expert but have you listened to make sure its not a fault with the wiper mechanism? as in the mechanism of bars that connect the wipers to the motor? Its not happened to me on my Z yet, but two 200sx's ive had, the mechanism failed when under wind/rain load - as in they would stay in middle of screen and would not function... this was down to the mechanism connecting cups (plastic) being worn. I might be miles off the mark but thouight I would mention it. -Stu

Have never seen that, only dead pixels :S not bad price :) ebuyer is very good price wise for stuff like that too, and always deliver on time.

Yeah they dont seem to look right at all, what a bout tyre roll? lol

Just googled the washers you are mentioning, neoprene looks ideal! The threads probably will strip again in the future - sods law, I will however keep your suggestion in mind, thanks m8 -Stu

Hi m8, yeah I managed to get a 1.5tap, would have preferred 1.25 but apparently that size is a bit like hens teeth for the M14(Where I 'borrow' my bits from tht is). The wheel bolt wasnt holding out so well so have now bodge a bit of steel rod and tack welded two nuts together onto the top of rod, again packed out with rubber washers and it seems to be working a treat :D Excuse mess of bay, but when its sprayed well over 40 litres over its self in the last 3 months, what do you expect lol - However, thats I think is just about every damn water hose been done on that car, finally I think its fixed! -Stu

Have tapped it to M14, and used a wheel bolt from a Peugeot, packed with some rubber washers - will be putting rad back in shortly so will let you know if it works! I imagine alot of ppl have snapped the original, plastic screw. FYI there was about 5mm alloy to tap, which has given me 3ish threads, seems to hold tight with the rubber though. -Stu

Hi Guys, A while back the black plastic bleed screw on the top of my Koyo decided to shear off, I found that an M10 bolt fitted nicely with some rubber washers - which worked up until last week... when I accidentally overtightened and stripped the threads in the alloy flange. I have attempted to tap it out to an M12, but all that did was make the hole bigger and only give it 1 thread (I have never tapped anything in my life... this may be the problem lol)... Does anyone know if i would get away with an M14 tap on the flange?!, or is it best to seek somewhere that can replace the flange with a new one? TIA Chaps, -Stu

Got mines today, many thanks Athene. -Stu

http://www.liveleak.com/view?i=2ac_1214710562 Amazing engineering.

Yep, played LFS since the beta days, good game - you wont find many if any other with physics like LFS :)