veilside01702

doesn't matter on pin 85 0r 86..... they are a coil that moves the connection from between pins 87a (NC connection = normally connected to pin 30 unless a 12v and earth are connected to pins 85 and 86) Then the connection is broken and pin 30 is connected to pin 87.... If using these diagrams please use a fuse on the 12v feed and also an unused crimp connector pushed onto the unused pin 87 to insulate it, as it could touch an earthing point and blow the output of you boost controller...... Only difference in diagrams is 12v feed.... first is from same point as boost controller and second is just any ignition feed....... Hope this makes sense..... it did in my head anyway...... lol

Only problem is that I jacked it on the main chassis rail as always..... I noticed the veilside bumper had split where it was bonded to the wing when I removed it.... but just thought it was due to body flex.... going to have to check what has happened when I get the side skirts and wing off this week.... Any idea how or if this can be rectified??

Removed front bumper again and fitted intercooler ducting, the fog lights fell into multiple pieces, Chrisbasildon dropped off my new side skirts...... :thumbup: .... thanks again Chris..... Top :nana2::dance:.... lol Had a visit from the lovely 'Craig' family for a cuppa and to pick up his new acquisition..... Then I refitted the horns properly behind the front bumper and realised my bonnet is bent upward a bit in middle as though pushed backward, my n/s/f wing is not straight and the gap between the wing and door is miles out at the top..... Looks like someone has pushed the front whilst it has been laid up on my driveway.... The gap on wing to door is huge at top and non existent at bottom now......

I always use these guys now as they have not let me down and use UPS and are usually one of the cheapest.......... You get to chose which quote and courier you want to use, how much insurance, etc..... http://www.interparcel.com

Jog On Allan........ lol

Oh and there are 3 listed addresses for people with exactly the same name in Sleaford in 2015?..... All the same age ?? I have all 3 addresses if anyone concerned would like them, I won't post on an open forum in case 2 of the addresses and names are not the low life involved in this so they can pass the details to the police of course.......:innocent:

Where's MINE....... No overnight delivery? What slack service Gary............ :whistling::tt2:

:slap: You just wait till I see you next........... My 3 year old will take you down.......... lol

Yes you are stuck with me for another year.......... MWOAH!!!! Another year of Veilside.......

Nobody took it, they just moved it a bit when spin was on the rig.................lol

Probably best to check V5 and HPI details against the stamped in chassis number, Witham is about 40 minute drive from mine........ Does look very familiar to me..........

Vin number on plate on front slam panel and stamped into bulkhead behind the plenum..... check they match each other and the HPI info.... Probably the DVLA got it wrong as it happens loads.... Mine came up as a Z31 not Z32...... some plank typed the details in wrong.... V5 is correct, but DVLA have wrong info on their system..... DOH What's the reg number? See if anyone here knows anything about it's history??

Well it was the gaskets you sent me for the middle lighting section that gave me the idea..... So it is down to you.... So thank you.......... I have had to trim them a bit on the corners as they weren't quite flush and I am missing half of the captive nuts to hold the rear lights in properly..... so when I get the replacements I will trim them to fit perfectly..... lol

Those new Irish Traffic police uniforms look good...... lol

I cut out some gaskets for the rear lights from neoprene sheet with an adhesive backing..... This is a rough fitting that I am trimming up to fit snugly.....

http://www.ign.com/videos/2013/04/30/star-wars-the-empires-may-the-4th-response

YAY........StarWars Day........ I shall be dressing as a character from the film today then ...... Years ago I was more of a Han Solo, but now more Jabba the Hut............

Is this the language you are all talking???:wink: [video=youtube;Omtfe7lb-gE]

I imported mine due to an EU Subsidy for migrant workers.........

Narrow painted top piece goes toward the front of car..........

But yours isn't a TT? ........:whistling:

Well I had an import NA auto........ Now converted to a TT and these fit both perfectly..... They bolted up to the Turbo downpipes 3 bolt holes perfectly and had No issues..... I got mine from Z centre in about 2001 - 2002....... They look exactly the same and clear everything and my exhaust has these, an H section and then 2 huge rear boxes....... it is loud....... Hope this helps...... just my experience with these..... I always wondered why people say they don't fit an Auto or TT or UK spec......

Bodymech 100%

Happy Birthday.......... :balloon::balloon::happybday::balloon::balloon: