Everything posted by jimmer
-
Has your tubs gone?
for 14bhp i wouldnt bother.some people have been lucky but there are loads that havent.leaving mine on as my tubs puff with the first boost then remain clear after.ive also been told by a zed garage who is well established that he would advise to leave them on the car as he has fitted them at the owners request and after a couple of months they come back and complain the cars smoking.
-
Grounding kits
of course not there hideous..havnt seen them in years.reckon the grounding kit will cure your static problem but i couldnt comment on them being a performance upgrade.
-
Brakes problem doing my head in,,,
take the pads back out and clean the paint off the edges that locate the pad in the caliper.likewise clean the inside of the caliper.make sure the pins arent corroded or bent.if the pads dont move freely in the caliper they bind causing the creaking noise.any car can suffer with this problem.just because the pads are new doesnt mean they wont do it.pad backs are painted with a thick black paint and sometimes you get paint drips on the edges that need cleaning off.10 minutes per side with a bit of emery cloth,light smear of copper grease and usually problem solved.
-
tightening handbrake
always adjust it at the wheels first.remove the back wheels and rotate the brake disc so the hole between the studs is about 25 past twelve as if you were looking at a clock.shine a torch in and youll see a toothed wheel.thats your handbrake shoe adjuster.what i do is put your handbrake on two clicks then adjust the shoes till the disc stops .once yove done this if the lever is still too high on the handbrake gaitor is a popper.undo it and below the lever youll see a long threaded shaft with a nut on it.hope this helps.
-
Grounding kits
hang some of those rubber strips from the back bumper.!!!!! :dance:
-
HID question
you can get bulb fitments for both.dips are h3c and mains h1 i think.
-
Brake Decelerometer?
what that means is they tested your car using a tapley meter.all mot stations have them if they test any permenent 4wd vehicles all though why they tested a zed using one is baffling.perhaps the rolling road died when graced by a zed!
-
Interesting Timing Belt Info.
always find the sprocket in fromt of the oil pump is the worst to get off.had one seized on an s13 and had to press it off the crank.the oil pump wasnt good for much after!! :rofl:
-
Interesting Timing Belt Info.
or just use an air gun with a shallow 27mm! :hyper:
-
possible gearbox and boost problems??
the filter is internal in the box.youll have to drop the sump on the gearbox to get to it.i wouldnt waste my time.brown oil and losing drive all points to one thing.ring an auto transmission specialist.my dads box kept slipping so i converted it.time to get your wallet out.
-
possible gearbox and boost problems??
if your box oil is brown then your box is on the way out.when the brake bands brake up the burning discolours the oil.time for a manual conversion.
-
Hey Legrath
was really surprised to see you in hallen of all places.were you avoiding the motorway and taking the scenic route?
-
turbo timer harness
you can wire them using your own loom like i did .done a search on google and found some bright spark that had fitted one to an rx7 wiring it himself.if i remember rightly it only takes 4 wires for most.an earth,handbrake signal and two off the ignition.
-
Hey Legrath
hi dave, was it you jason and me passed going through hallen just after 3 today.could have sworn it was you?
-
More Pics Of Japfest
thats driving ivan from bristol.
-
Battery Light On
check the "engine cont" fuse.its under the bonnet with the fuses and relays located on the inner wing.
-
Rear suspension help
the rear suspension arms are on eccentric bolts for small adjustments.the most common 300zx problem is bent rear lower wishbones from a sideways kerbing.i would compare the wishbones to see if ones bent.
-
piston markings
best way to check is to measure the piston.thats what i always do.check the manual for oversizes and compare.then pray yours arent at maximum!.
-
advice needed............slightly worried
is the noise half engine speed.if it is then it probaly is from the valve train.is it a rattle rather than a knock.the variable cam timing operates at 3000rpm this can make noises if the springs in the hubs go weak.to prove this on the back of each rocker cover nearest the middle of the engine is a solenoid.trace the wires that come out of them and unplug them.run the engine then see if the noise goes.if it goes you have a vtc fault.check the feeds at the plugs supplying the solenoids.the correct voltage is in the nissan manual.if the feeds are there then its time to replace the vtc springs.
-
Speedos
honestly though only the cheap delimiters fail.got uk clocks in yours dave?
-
EGR AIVV stuff
removed my egr when the engine was out.be a pig otherwise.the pipes on the plenum are fiddly enough but the supply pipe from the n/s is a bit more tricky.i cut the flanges off to the plenum then pool welded the holes up.bin the pipe from the turbo elbow but keep the nut that secures it.also pool weld the center of the nut then refit to to the elbow.remove the valve then follow the vacuum pipe back to the o/s inner wing and blank off job done.
-
Speedos
delimiter takes 20 minutes to fit and the clocks an hour.know what id do.
-
Speedos
sounds like the car is still restricted.does it chime at 100kmh and will the car go off the clock?.if not you need a delimiter fitting.
-
Headbolts....stretchbolts?
si im sure i told you earlier that the the head bolts dont need replacing on a z32. :nono:
-
MAF Mesh
the mesh over the maF IS TO PREVENT DEBRIS and sticky fingers touching the element.had them at work where a blade of grass has gone through and broken it.the element is very fragile.if a leaf got sucked in and shrouded the element it wouldnt be able to determine air flow.