syed rahman

So these pads are the same fittment for Jap and UK spec or are there variations in part nos. and sizes ?

I'm glad u mentioned driving like ms daisy. The mrs. on the Zed the other day, I nearly crapped myself. I got out shaking like a leaf ! I didn't know she could drive like that, redlining all the way through. That chip you fitted is lethal, what is it called ? It felt like if the car had wings it would take off into the air.

So whats so great about the red and green stuff ? Why are they so expensive ? Thanks for that Ryan & Taff

Any recommendations on what pads to use all round ? I have Brembos. Also is there any difference between JAP Spec and UK Spec pads ?

I ordered a car bra from Courtesy Nissan on Tuesday night and it was at my doorstep Thursday morning at 9am ! I must say the Yanks have a damn good delivery service.

My Z31 was in storage for a while and the handbrake was up. When it was finally started again, the cable was severley jammed. The hand went down but wouldn't release the mechanism. At the end I dragged the car in first gear for half a mile before it unlocked !

Thanks guys..

When I hear big ends and bottom ends, I get chills down my spine. I have had so much bad luck with my Supra with bottom and big ends, its very expensive job.

I am a bit confused here thus someone please elaborate. I have a stock spoiler with the black strip going underneath it from end to end. Now if I was to fit a perspex cover, will that replace the strip or will I need to get rid of the entire spoiler for it to fit. Basically, that damn strip is a nuisance and I have replaced it a few times but it always seems to look kak as it bubbles up etc. I need to find a solution to this. Thanks.

Check fuel line blockages, injectors and coil packs...

These look like my Enkei Koyoho alloys !

Is there a link here for a DIY in replacing front stabilizer bushes. My steering right now is kak and need to do this asap I am told. Infact, what do these things look like and where fu*k are they meant to be ? Can anyone post a pic or drawing or something as I don't want to take the wrong thing off ! Also do I need any special tools ? Finally, where do I buy these from and how much ? Thanks all...

ehh no, not without serious mods to the engine bay I think and also would need bell housing complete with corvette gearbox...

Rich, I am due to do the same tomorrow from the pipes I got from Smithy, hence I need to know as well. By the way, how did you start off, did you just go around in any particular order ? And how did you distinguish the sizes ?

Where do you guys buy this mesh from and how do you stick them on ?

I've seen one as well, a saxo with tights on the rear lights, weired....

MJP Eastern, trader on this forum, I have ordered mine through him and hopefully should get delivery on Monday as stock has arrived from Japan. Not cheap to buy but well worth it if you want to cater for HICAS and cruise. Give him a ring.

Now, before everyone thinks I've gone crazy and lost the plot, just hear me out on this one. Back in the 80s when the punk look and leg warmers and leotards were in fashion, some of us (not all) tinted out our Capris, XR2s and Mantas front headlamps with this shinny stuff that you sprayed on. While the lights were off they gave a mirrored look. Any ideas what that spray or tint was called ?

Do what thou heart tells you to do....but whatever you chose to do think twice before doing it....

Don't have this sort of problem with the Supra & Porsche Clubs ? My neighbours with Supra TT and Porsche 911 are proudly displaying their club, shame I can't ? In my opinion, it would have been far more sensible and noble to send all of us the stickers at the same time instead in drip and draps, thus all could have shared similar feelings. Just want to know why some have got them while others have not when names have been on the list from day one of membership ?? Do I and a few others have to be more privileged members to receive this honourable service ? Its a point of principle than the stickers themselves. Forgive my approach but this is bad shoddy management and I am entitled to my opinion.

Thank you to all, and a big thankyou to Matt (Paul's son) for taking the trouble to ring me, what would I do without you guys ?

oh you dirty man...LOL

Thanks but I need info on the removal of an auto shifter stick. How do I take it out ? I mean where are the screws ? There are none on the the handle etc.

I guess no one here has replaced their auto stick then ?

I use Immac to go smooth - All Over