vijay

if you do, don't bother replacing them with Nissan ones - use universal steering gaitors - much cheaper :) Vijay

Hi Kev, Been around here for a while and can't recall hearing anything about that company. All I would say is there are plenty of mechanics/garages who say thay can work on 300's but only a few who know what they were doing. Good luck :) Vijay

Cheers guys. Yes Chris I was just looking for an easy way to swap files over. What's the link suppsoed to go to? Cheers Vijay

Morning, Just wanted to know if I can network a pc and a laptop by USB cable at all or does it have to be done by an RG45 cable? Cheers Vijay

I'm looking at buying one soon for any car work and I might want to make up a gate. What should I be looking for as a total novice? Cheers Vijay

I suppose it's me next :) can I have a bottle of brandy please, I'll PM you my address. Cheers Vijay

Hello Mark, You can drive the front wheels onto some bits of 4x2 timber which will allow enough clearence. The rear gets lift from the dif - http://www.300zx.co.uk/cgi-bin/manual.cgi?list=gi&dir=&config=&refresh=&slide=22&cycle=off&scale=0&design=default&total=25 Vijay

Have a read here - http://www.twinturbo.net/ttnetfaq/FAQpages/O2s.html

My mate actually used a kit from Halfords with very good results. Vijay

http://www.ttzd.com/tech/pcvtech.html not a difficult job, just akward. You'll need a set of long nose pliers :) Vijay

Why not give Mike Feeney a call - 01277-374201. Vijay

Hi Robert, I beleive you can just use glass paint :) Vijay

Hi Poozer, You won't have a problem with the MOT if you have a read of this thread - http://www.300zx.co.uk/forums/showthread.php?t=27060 Mine failed and thanks to PaulC, I went back with a print out of the page and they passed my car :) Vijay

Is this any good Steve? - http://www.300zx.co.uk/cgi-bin/manual.cgi?list=el&dir=&config=&refresh=&slide=88&cycle=off&scale=0&design=default&total=133 Vijay

http://www.twinturbo.net/ttnettech/tc/tc.html

Hi Derek, Defo get rid of that Turbo Technics breather kit, it caused oil starvation IIRC. Vijay

IIRC, Tarox had a reputation of disks warping. Vijay

the last restore point didn't work. I've booted it up in safe mode with DOS prompt and I can run chkdsk but it says "invalid parameter - /p". I ran just chkdsk with no parameter and it found errors and said to run chkdsk with a parameter of /f. Is that the way to go?? Cheers Vijay

it's booted up in safety mode - what next??

does it matter if my copy of XP is not bootable? (at least I don't think it was)

old configuration (which stopped working) was a Maxtor drive running xp was the master and a Wester Digital drive was set up as a slave. What I have done is removed the Maxtor (with XP on it) and I have installed ME onto the WD drive. I then plugged in the Maxtor as a slave so I can access the files.

nope, last know configuration didn't work either :( Bye the way I can access the drive as I've set it up as a slave if that helps

or you can get a small device which will keep your battery topped up (goes between a charger and your battery), not sure if that would affect your alarm though. Vijay

Urgently need some help here :( While loading Zonealarm yesterday, my pc (running xp) decided to lock up. It will not boot up at all (not even in safety). On the normal boot up it just hangs on the initial windows screen (where you get the blue loading bar going from left to right on the bottom). Any ideas???? I needed to get some photos off urgently so I put a different HDD in and loaded windows ME (Only disks I have), it took over 12 hours to load but it will not recognize the CD roms, any ideas on that? Cheers Vijay

I've been using Norton for the last few years and it's time for renewal. Just looking for ideas of what's best for anti virus and firewall software. Cheers Vijay