If you fit an afr meter to your car.do they go were the 02 sensors use to go or do i need to buy some hole things and get my exhaust man to weld them in somwere.

I fitted mine last week, take my advice , get the kit FIRST, then get under the car and decide where to place it , as you have been told 10 degrees above horizontal, perpendicular to the flow, you will find that with the sensor in your hand and the guidance of angle and distance that there are only 1 or 2 places it can go, Mine is fitted at the rear of the AUTO box cross member and the electrics passed into the cabin via the original CAT sensor bung, my Wide Band used an 18mm bung, but like I said do not try and fit anything up until you can decide on position exactly by getting under the car.

Which kit did you buy sayers and why?

Joke mate! Dont take affence as none intended dude.appoligise if i affended you.

 

 

Oh and just to say that i havnt got any peace of kit yet as i havnt decided whitch best route to go down

 

Sorry, my bad. Didn't read it as such :blush:

Whos got what wideband controllers.?

 

I have a pair of these

http://www.aemelectronics.com/?q=products/gauges/failsafe-gauges/wideband-failsafe-gauge

http://www.300zx.co.uk/forums/showthread.php?180685-AEM-Fuel-pumps-FPRs-EBCs-Wideband-AFR-Kits-amp-MORE!

SpinDoctor, save yourself a world of hassle and buy the right gear from Noel, (NOZ)

http://www.300zx.co.uk/forums/showthread.php?180685-AEM-Fuel-pumps-FPRs-EBCs-Wideband-AFR-Kits-amp-MORE!

 

Is this bit of kit that you work with and install Noel or is it a just a one off peace of kit that you have for sale.? If it is one that you highly recomend and work with how much is it .one as a kit and two how much fitted.pm if needed ref to your pricing.oh and im asuming this will work well along side that nistune i bought?

Thanks.

It's the same AEM kit I sold to bigh and quite a few others. I sell AEM items, HKS, Exedy, Competition Clutch etc.

 

I don't do any mechanical work nowadays, there are others much more suited to it. I mean, imagine if I hit my fingers with a hammer, how would I press the [more BHP] key on my laptop :wack:

 

The AEM kits have an output that can be used in the Nistune software to display AFR on a laptop.

 

Prices are on the thread, £295 for 2 kits, 1 for each bank. Think I've just sold my last pair, so may be a slight delay before the next batch*

 

*Edit: Have sold them but more are available :)

Edited April 25, 201510 yr by Noz

It's the same AEM kit I sold to bigh and quite a few others. I sell AEM items, HKS, Exedy, Competition Clutch etc.

 

I don't do any mechanical work nowadays, there are others much more suited to it. I mean, imagine if I hit my fingers with a hammer, how would I press the [more BHP] key on my laptop :wack:

 

The AEM kits have an output that can be used in the Nistune software to display AFR on a laptop.

 

Prices are on the thread, £295 for 2 kits, 1 for each bank. Think I've just sold my last pair, so may be a slight delay before the next batch*

 

*Edit: Have sold them but more are available :)

cheers Noel. Looks like there be on my list too then.

Spin see my thread "Powerzed engine rebuild" as I have some more info for you regarding positioning widebands

Spin see my thread "Powerzed engine rebuild" as I have some more info for you regarding positioning widebands

 

Cheers Howard.