Jump to content
View in the app

A better way to browse. Learn more.

300ZX Owners Club

A full-screen app on your home screen with push notifications, badges and more.

To install this app on iOS and iPadOS
  1. Tap the Share icon in Safari
  2. Scroll the menu and tap Add to Home Screen.
  3. Tap Add in the top-right corner.
To install this app on Android
  1. Tap the 3-dot menu (⋮) in the top-right corner of the browser.
  2. Tap Add to Home screen or Install app.
  3. Confirm by tapping Install.

DGM

Dormant Member
  • Joined

  • Last visited

  • Country

    United Kingdom

Everything posted by DGM

  1. F*** ten times worse than mine, i'm sure its the drain tube that terminates at that point which causes the problem.
  2. Just replaced passanger side inner and outer sill/quarter panel with repair panels on mine and am about to fit drivers side sill/quarter repair panel. The rust in this area had eaten the metal from the inside hence by the time it was noticed it was quite bad.Few bits of rust round wheel arches due to chipped paint, passanger door has a bubble at the bottom. Still i would say the car is solid for its age ( I've also got a stag and a capri).
  3. Disks - once caliper is out the way just give them a tap with a rubber mallet and they should come of.
  4. DGM replied to a post in a topic in General Discussions - 300ZX Related
    Gurgling?
  5. Air injection valves are under the wings, they send are to the manifold under certain conditions, if not functioning properly they 'gurgle'.
  6. Borrowed this from a previous post, cheers. Taken from the FAQ section of TT.NET... Does my automatic Twin Turbo really have 20 horsepower less at the flywheel? Yes. I couldn't believe it, based on the performance of the two cars, so I did some research. I found two quotes from books written about the Z: "The four speed automatic was also available in the Turbo but in deference to the auto boxes longevity, the engines power output was cut back to 280bhp by different camshafts and fuel injection maps. Torque remained the same." From: Illustrated DATSUN/DATSUN Sports Car Buyers Guide by John Matras. and: "For various reasons the 300zx Turbo in some versions is rated at 280bhp. This applies to the Japanese market, where the manufacturers have an agreement to limit outputs to 280, to automatic trans models in the US, which have different camshaft profiles and fuel injection settings, and to the European market 2+2 because of its setting for lower-octane unleaded fuel." From Nissan 300ZX - The Enthusiasts Companion by Ray Hutton I asked people I know at Nissan USA and Nissan Japan to confirm the horsepower rating of TT's with automatic transmissions. The response I got from a contact at Nissan USA was: "Aside from minor changes in the ECU, the cam profiles & turbos are also different between the M/T & A/T models. The A/T has 240 degree intake cams & 248 degree exhaust cams (the M/T has 248 degree cams for both intake & exhaust). Also, the A/T uses smaller turbos for more responsive low speed acceleration (the A/R ratio is 0.63 for the M/T & only 0.54 for the A/T). Even with 20HP less, the A/T turbo is capable of beating the M/T turbo to 100MPH." I checked the fiche in the 'DOCS' section: There were always different ECU's for manual and auto cars. The camshafts were always different on the autos until the 1996 model year, and the part numbers changed three times. In 1996, Nissan discontinued the variable valve timing system, and rated the TT engine at 280 HP. The exhaust manifolds (from the cylinders to the turbos) are the same for all years. The turbos were always different (see Nissan USA comment above). They went through two part number changes on the right hand one, and three on the left hand one. The exhaust housings (which attach the pre-cats to the turbos) were different for manuals and autos only from 9/93 to 9/94. The manual and auto had different pre-cats, and the part numbers changed three times from 1989 through 1995. Both cars used the same pre-cat for the 1996 model year. The H-pipe was the same for both manual and auto cars throughout production. The main mufflers were different throughout production - even for the 1996 model year. The auto has a different radiator, to accommodate the need to cool the transmission fluid. There were no part number changes throughout production. From all of the differences in components, it's pretty clear that Nissan did some serious engineering to get the two cars to perform much the same way even though the auto model is down 20 HP.
  7. Again not 100% but, yes different sized tubs but also different engine components to negate the difference.
  8. I could be wrong, i could be right, all TT'S 280 except possibly the US market got 300?
  9. DGM replied to a post in a topic in General Discussions - 300ZX Related
    Sounds standard mate, dont think you have anything to worry about. If you've got the monet then by an aftermarket system.
  10. Take a nissan one with you Rich, there only a fiver, your still not having to do the job yourself.
  11. Fraser, that was the way i was thinking of doing it, i just here stories about welding and MOT's and get worried that i go to a lot of bother and it's not the MOT way of doing things. Cheers
  12. Good Point, Slick
  13. Did you get a nice finish, i used to do this kind of work in my teenage years, just worried that the way i'm used to doing it might not be accepatable now. cheers for the reply
  14. Excuse the ignorance, but what is an oil catch tank?
  15. The car in front is a Black one ;)
  16. Someone else might come along with a better suggestion, but check for oil leaks at the top right and left corners of the engine (near the battery on the passanger side) coming from the PCV rubber pipes. Its a bit of a long shot.......but worth a go.
  17. Failed the MOT today on rusted sills. Anyway, i'm going to order repair panels in the next couple of days and do the job myself. Question, is it ok, as per the MOT standards, to drill holes in the bottom and wheel arch flanges and mig weld them and to but weld the rest? cheers
  18. have you checked your PCV valves
  19. Think your a top gun?
  20. Was that Indian ZX in his new toy
  21. Does it drink a lot of water
  22. :tongue:

Important Information

Terms of Use

Configure browser push notifications

Chrome (Android)
  1. Tap the lock icon next to the address bar.
  2. Tap Permissions → Notifications.
  3. Adjust your preference.
Chrome (Desktop)
  1. Click the padlock icon in the address bar.
  2. Select Site settings.
  3. Find Notifications and adjust your preference.