hello I wonder if the configurations of the APEXi SAFC II station right

Followers

September 2, 201312 yr

SETING

TH POINT LOW 30 HI 50

DEC AIR

THR 48 %

NE1 1.2%

NE2 2.7%

KNOK SET

0 RPM

1: 0 1500RPM

2: 0 3500RPM

DATA FILE

FILE 1 :ON

FILE 2 :OFF

ETC

SENSOR TYPE : HOT-WIPE

CAR SELECT 6

DISPL SCL

PR 2.0Kg/Cm2

NE 8000RPM

CR +/- 30%

WARNING SET

KARW 1600Hz

KNKW 40

REVW 8000RPM

if you have something wrong please help me

forged piston and connecting rod

thanks :tongue_smilie:

Quote

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.

Unfortunately, your content contains terms that we do not allow. Please edit your content to remove the highlighted words below.

Reply to this topic...

Followers

Go to topic listing

No registered users viewing this page.

No registered users viewing this page.

My daughter calls it Toothless the Dragon: My ‘95 TT Z

Haven’t messed with Play Doh for probably 40 years 😅. Cam timing has been finalised, so was time to check piston to valve clearance. Turns out I’ve got LOADS. 4.4mm on intake and 4.9mm on exhaust. Finally day of tinkering complete before the family holiday to Sicily. Straight back to it when I’m back, and hopefully take delivery of my new Singapore swirly boys

By nickz32 · 3 hours ago3 hr
JaiKai - MK2 - Ziggy Build

New engine oil arrived yesterday so had some time today and got the engine how i liked it ready to be put back in.
But this time i've decided to move the wideband sensors back to the downpipes as i still dont like the location the test pipes
that i have with the proper bungs put them at and for my likening its a little low.

All ready to be put back in the zed.

By JaiKai · 8 hours ago8 hr
My daughter calls it Toothless the Dragon: My ‘95 TT Z

More progress. Verifying the cam timing and found the exhaust cams were off by 3 degrees. Surprised that the intake cams were spot on where the should be considering the new block and heads being skimmed.
Next job is adjust the cam timing to get it to spec, then pull the heads off and play doh the pistons and check Piston to Valve clearance. Will also advance the intake cams 10deg to simulate VTC activation and make sure everything has plenty of room

By nickz32 · Wednesday at 19:431 day
Simply Japanese at Beaulieu 19th July 2026

I was hoping to push on and potentially make this, but my turbos that were meant to be delivered tomorrow have been pushed back until end of the month

By nickz32 · Monday at 20:333 days
Simply Japanese at Beaulieu 19th July 2026

Bringing this back to the top - as it's the next big event in the car show calendar....
....And NEC aside, this is really one of the year's best car shows. Great location, so much to see in addition to a huge variety of Japanese cars, and (hopefully) good weather.
I haven't booked a club stand (yet) as the organisers need a minimum commitment of 10 cars - but there's still time!
Even if there's just a handful of us, we can meet up at the usual location (Tescos car park) and drive in together.

By RichardS · Monday at 18:193 days

hello I wonder if the configurations of the APEXi SAFC II station right

Featured Replies

Join the conversation

Recently Browsing 0

Recently Browsing 0

Popular Posts

My daughter calls it Toothless the Dragon: My ‘95 TT Z

JaiKai - MK2 - Ziggy Build

My daughter calls it Toothless the Dragon: My ‘95 TT Z

Simply Japanese at Beaulieu 19th July 2026

Simply Japanese at Beaulieu 19th July 2026

Important Information

Account

Navigation

Search

Configure browser push notifications

Chrome (Android)

Chrome (Desktop)

Safari (iOS 16.4+)

Safari (macOS)

Edge (Android)

Edge (Desktop)

Firefox (Android)

Firefox (Desktop)