boldy

The rear quarter windows are tinted as standard , don,t try and remove this !

Thats one way of taking the head off :x: :x:

Word of warning !!! If you wanna stand near darrens motor ...WEAR EAR PRETECTORS... By fook its loud, but sounds the mutts :bow: :hyper: :hyper: :hyper:

Yep , only dumps when you take your foot off the gas .

Hope you find a nice one bud and if you buy it BE CAREFUL with your right foot until you get used to it :shock: :shock: The power can catch you out on corners :bow: :bow: Welcome to the forum :hyper:

Thanks :hyper: :hyper:

At least the guys honest, which can be a rare on ebay , 32 bids as well :bow: Funny as fook though :hyper:

I bet he felt a bit woof after that :D :D :D I,ll get my coat :headvswal

Nice one Tony , about time you had a proper car :D in a proper colour as well :bow: :bow: Looks sweeeet :hyper:

No probs bud .

The yellow ones for the ECU

I moulded them out of fibreglass and bonded them to the nose panel with the same , there fastened to the headlamp glass with a couple of blobs of silicone :hyper: Not to everyones taste but theres nowt wrong with being different :D The ebay ones are too big to me

Somebody said on here once , if the front tyres are wider than is fitted on a standard 16inch wheel it can cause this , i know mine does it :headvswal :headvswal

This might help http://www.300zx-mods.co.uk/Interior.htm

They,ll be a standard boss though not a Hicas boss HTH

I,ve just replaced mine with an after market one , my originals in very good condition , off a jap tt , £45 delivered if your interested i,ll take some piccies :hyper: :hyper:

Not before i do !!!! HUBBA HUBBA :bow: :bow: :bow: :D

I stuck mine down using 3M re-fix tape , its basically a sticky glue on a backing , pull the backing off and only the glues left behind , if not that then i would have used carpet tape as its very thin and won,t make the needle,s catch the faces . Ooh by the way , theres no need to remove the steering wheel !! :hyper:

I moulded my own and blended em in ,its the only one that i,ve seen done like this :hyper: :hyper: :hyper: :hyper:

Hi Tim , i found it easier to warm the whole glass with a fan heater so its evenly heated , less chance of cracking them , also use a wide bladed scraper to prise the glass off its bonding , if you use a screwdriver the glass chips very easily , hope you get em sorted bud :hyper:

I think the main problem is water dripping down between the nose panel and front bumper which is directly above the filter ,this seems to happen more if you have an after market nose panel, i also had this problem . :headvswal It was easy to sort out ,remove the nose panel and make a flat plastic shield to sit over the filter and use the front two 10mm bumper bolts to hold it in place , it directs any water to each side of the filter rather than on it. :hyper: :hyper: HTH

Hmm Momo about £50 or this one for £19 :tongue: :tongue: :tongue:

Cheers Speedemon , got the handle of a seller on ebay called Car Wizard who do a range of steering wheels , handbrake handles and gear knobs made buy Enzo Styling ,the handles turned out of solid aluminium and has a bore of 22mm which turned out to be slightly smaller than the Z handbrake :headvswal :headvswal . I,m gonna put piccies and a write up on how i fitted it in the FAQ,s section under tuning and mods ( if i can shrink these bloody pictures )

Got round to fitting my new steering wheel and handbrake handle :dance: :dance: Sorry about the big piccies , shrunk em on photobucket but still coming out full size :smash: :smash:

PMSL :slap: for Rich next time i see ya :rofl: :rofl: :rofl: :rofl: