fiat rear panel

Followers

January 3, 200719 yr

hey guys i bought the fiat light rear panel (like vijays') from luke, with the thought of putting in fiat lights. i'm now keen on the lambo lights and was wondering if they would fit straight into the panel i've got as its already bonded into place!!!

Quote

January 3, 200719 yr

hey guys i bought the fiat light rear panel (like vijays') from luke, with the thought of putting in fiat lights. i'm now keen on the lambo lights and was wondering if they would fit straight into the panel i've got as its already bonded into place!!!

The Lambo lights are bigger i think , they,re the same size as the ones i,ve got fitted cos i had a choice of these or Lambo , but i,m sure you can fit the Demon L.E.D lights instead of Fiat as in the yellow Z below. HTH

Quote

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.

Unfortunately, your content contains terms that we do not allow. Please edit your content to remove the highlighted words below.

Reply to this topic...

Followers

Go to topic listing

No registered users viewing this page.

No registered users viewing this page.

UK Importers Advice

I used Josh @ Gorilla Imports in 2021. My first time importing and was a very good experience.

By sumshiftyguy · 4 minutes ago4 min
Tyre size recommendations

245 on an 8J will look like a balloon on a 8j….. an 8J is only 204mm wide

The tyres you currently have a 2% smaller in diameter and circumference that the OEM wheel/tyre combo

Personally would be looking at a 225/45r17. Plenty of very nice tyre options and only 0.4% different diameter from OEM size

By nickz32 · 10 hours ago10 hr
Simply Japanese at Beaulieu 19th July 2026

If I’ve built and installed my engine by then (which I bloody hope I have!) I’ll be there

By nickz32 · 10 hours ago10 hr
Suggestions for Potential Valved Exhaust

Personally I wouldn't bother mate!
Valved systems are fine where they are an OEM fit on new cars, but why waste cash trying to replicate that on an older car which sounds pretty decent from the box.
Go and speak to Infinity (the guys next to Jim) and get them to custom build a "normal" system for you. I did and I am very pleased with the result.
My old Mongoose was too intrusive at cruising speeds, so Infinity fabricated one with extra resonators at the front, which made cruising quieter from inside the car. They then used smaller silencers at the rear, so the best of the noise is out back. If I want to have a little fun and enjoy the rumble, I just open the windows.
No fancy switches to mess around with, it looks good, sounds good (without the added knob-headed attention seeking function) and only cost £600 all in.

By RichardS · 10 hours ago10 hr
Tyre size recommendations

Hi Rob,
for the wheel sizes you have, and to keep the rolling circumferences close, fronts should be 45 profile - go for 235/45/17 on the front and 255/40/17 on the rear. You'll find plenty of options with those sizes. That's what I ran when I had the same 17 inch Azevs on my red Zed😉
You might get 265/40/17 on the rear - but brand options may be fewer.
It all follows when you upgrade wheel diameter, you keep the width and drop 5% in profile - I have 18s and my fronts are 235/40/18.
Richard

By RichardS · 11 hours ago11 hr

Sign In

fiat rear panel

Featured Replies

Join the conversation

Recently Browsing 0

Recently Browsing 0

Popular Posts

UK Importers Advice

Tyre size recommendations

Simply Japanese at Beaulieu 19th July 2026

Suggestions for Potential Valved Exhaust

Tyre size recommendations

Important Information

Account

Navigation

Search

Configure browser push notifications

Chrome (Android)

Chrome (Desktop)

Safari (iOS 16.4+)

Safari (macOS)

Edge (Android)

Edge (Desktop)

Firefox (Android)

Firefox (Desktop)