Right.

I thought i might ask what people might expect as a Dyno figure from a car with the following:

Blitz Induction

De-cat Scarab exhaust system

JD (Medium agressive Chip)

Boost contoller set at 14.5 psi

 

Optimax and Nitrox octane boost fuel mix ;)

My car goes into Wilcox racing developement tomorrow to get checked out and Dyno'd.

 

I would like proper figures and not daft ones :nono: as i know you lot :D Not had her done before so dont know what to expect :confused:

Cheers Guys

Matt

Right.

I thought i might ask what people might expect as a Dyno figure from a car with the following:

Blitz Induction

De-cat Scarab exhaust system

JD (Medium agressive Chip)

Boost contoller set at 14.5 psi

 

Optimax and Nitrox octane boost fuel mix ;)

My car goes into Wilcox racing developement tomorrow to get checked out and Dyno'd.

 

I would like proper figures and not daft ones :nono: as i know you lot :D Not had her done before so dont know what to expect :confused:

Cheers Guys

Matt

 

Similar mods to mine Matt. Would estimate around 300 RWHP (about 350 at the fly). Interested to see what you get with the octane booster as well...

 

Steve :)

The octane boost is The Black Nitrox bottle ;) 20 points or 2 Octane boost. Put it in the car today and took her out for a spin and after about 3-4 miles she seemed to pick up a tad better:cool: but that could be down to her getting warm and settling down.

But hey, shall wait and see :D

hi sarge

 

i would guess at about 315 rear wheel bhp your on the limit of the clutch slipping at this kind of rw power so maybe a usefull mod in the future would be a twin plate street race clutch , just an idea

I estimate 297rwhp!!

 

:D

simular to mine mate

357 at fly

 

steve

hi sarge

i would guess at about 315 rear wheel bhp your on the limit of the clutch slipping at this kind of rw power so maybe a usefull mod in the future would be a twin plate street race clutch , just an idea

Steve, ;) Me got a RPS Sport street clutch in bud.....:cool: :nana2::nana2:

Steve, ;) Me got a RPS Sport street clutch in bud.....:cool: :nana2::nana2:

 

Be better if you got the ECU mapped for the higher octane, have 2 eproms 1 for pump and one for higher octane fuel.

checked with the guys on the US boards, and they say 4000 bhp at the wheels. :D

Similar mods to mine Matt. Would estimate around 300 RWHP (about 350 at the fly). Interested to see what you get with the octane booster as well...

 

Steve :)

 

You will not get any extra power from using Octane booster :( ........unless of course your using a boost controller etc then you may be able to squeeze a little more power from that and make use of the higher octane fuel

 

Ryan

Ryan, i will have the B/Controller set to 14.5 Psi mate she can run a bit more ;) but just want to see what figures i get this time as not ran her before.

Ryan, i will have the B/Controller set to 14.5 Psi mate she can run a bit more ;) but just want to see what figures i get this time as not ran her before.

cool, at the end of the day it will give you a little more protection which is never a bad thing :)

 

Ryan

Well got 2 hrs before she does her runs :confused: hope she does me proud :cool: So we think she should be betweeen 297 and 315 RWBHP ;)

I shall post the results either way :confused: Chunk's going to be there to support or take the p1ss :rofl: me thinks the latter :D

Fingers crossed it all goes well Sarge :cool:

Fingers crossed it all goes well Sarge :cool:

:duffer: Cheers Mac and yours when she comes out to play bud :cool:

checked with the guys on the US boards, and they say 4000 bhp at the wheels. :D

 

lol :D

:duffer: Cheers Mac and yours when she comes out to play bud :cool:

 

LOL I thought ahead and bought 40 sandbags off Ebay :rofl: ;)

Right.

I thought i might ask what people might expect as a Dyno figure from a car with the following:

Blitz Induction

De-cat Scarab exhaust system

JD (Medium agressive Chip)

Boost contoller set at 14.5 psi

 

Optimax and Nitrox octane boost fuel mix ;)

My car goes into Wilcox racing developement tomorrow to get checked out and Dyno'd.

 

I would like proper figures and not daft ones :nono: as i know you lot :D Not had her done before so dont know what to expect :confused:

Cheers Guys

Matt

 

I have similar mods to you, I have 325bhp at wheels at 15.5 psi.

Well i dont know if this is good or bad news :confused:

She got

290.5 rwhp at 6000 rpm and 296.5 lb/ft torque but as chunk will tell ya they had to put 2 blokes in the boot cos she was spinning...:rofl:

So whats the verdict and whats the Fly wheel Bhp for those in the know..:D

Cheers Matt

 

Cheers Mac so 348.6 FWHP....aint to bad then :D

Around 20% more mate;)