noise from clutch i think

Followers

March 21, 201015 yr

scraping noise when in neutral but when i press the clutch in it stops i can hear it the loudest in second gear barley in 3rd and not at all in the other gears.

hear is what it sounds like on some ones car on youtube

what is going on aggggggggggghhhhhhhhh?:headvswal

Quote

March 21, 201015 yr

usually the release bearing with them symptoms

Quote

March 21, 201015 yr

yep thrust bearing is noisy by the sounds of it.

Quote

March 22, 201015 yr

When the clutch pedal is depressed the first motion shaft stops spinning in the gearbox and the release bearing is under load, so it still could be the input shaft or idler gear bearing within the gearbox.

Jeff TT

Quote

March 22, 201015 yr

Mine is the same, but hey.....gearbox rebuild is looming.

Al.

Quote

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.

Unfortunately, your content contains terms that we do not allow. Please edit your content to remove the highlighted words below.

Reply to this topic...

Followers

Go to topic listing

No registered users viewing this page.

No registered users viewing this page.

Tyre size recommendations

245 on an 8J will look like a balloon on a 8j….. an 8J is only 204mm wide

The tyres you currently have a 2% smaller in diameter and circumference that the OEM wheel/tyre combo

Personally would be looking at a 225/45r17. Plenty of very nice tyre options and only 0.4% different diameter from OEM size

By nickz32 · 10 hours ago10 hr
Simply Japanese at Beaulieu 19th July 2026

If I’ve built and installed my engine by then (which I bloody hope I have!) I’ll be there

By nickz32 · 10 hours ago10 hr
Suggestions for Potential Valved Exhaust

Personally I wouldn't bother mate!
Valved systems are fine where they are an OEM fit on new cars, but why waste cash trying to replicate that on an older car which sounds pretty decent from the box.
Go and speak to Infinity (the guys next to Jim) and get them to custom build a "normal" system for you. I did and I am very pleased with the result.
My old Mongoose was too intrusive at cruising speeds, so Infinity fabricated one with extra resonators at the front, which made cruising quieter from inside the car. They then used smaller silencers at the rear, so the best of the noise is out back. If I want to have a little fun and enjoy the rumble, I just open the windows.
No fancy switches to mess around with, it looks good, sounds good (without the added knob-headed attention seeking function) and only cost £600 all in.

By RichardS · 10 hours ago10 hr
Tyre size recommendations

Hi Rob,
for the wheel sizes you have, and to keep the rolling circumferences close, fronts should be 45 profile - go for 235/45/17 on the front and 255/40/17 on the rear. You'll find plenty of options with those sizes. That's what I ran when I had the same 17 inch Azevs on my red Zed😉
You might get 265/40/17 on the rear - but brand options may be fewer.
It all follows when you upgrade wheel diameter, you keep the width and drop 5% in profile - I have 18s and my fronts are 235/40/18.
Richard

By RichardS · 11 hours ago11 hr
UK Importers Advice

Not the same motor.
Mine was originally blue, and I done a full break down and refurb with a full respray to purple.

By JaiKai · 11 hours ago11 hr

Sign In

noise from clutch i think

Featured Replies

Join the conversation

Recently Browsing 0

Recently Browsing 0

Popular Posts

Tyre size recommendations

Simply Japanese at Beaulieu 19th July 2026

Suggestions for Potential Valved Exhaust

Tyre size recommendations

UK Importers Advice

Important Information

Account

Navigation

Search

Configure browser push notifications

Chrome (Android)

Chrome (Desktop)

Safari (iOS 16.4+)

Safari (macOS)

Edge (Android)

Edge (Desktop)

Firefox (Android)

Firefox (Desktop)