Anyone recommend a good high fill primer?

Followers

August 22, 200916 yr

As above. I'm smoothing the stonechip, currently using plastikote Spot filler and primer. Just wondering if there's a better one?

Quote

August 23, 200916 yr

I'm guessing you are using spraycans when you mentioned plasticote? Not going to get a high build primer / filler in a can unfortunately...

Do you have access to spray gun / compressor? If you do I would do a couple o coats of 'Reface' and it would be smooth and sexy.

Quote

August 23, 200916 yr

Don't use high build primer as a filler on the bumpers, just get rid of the finish!

Quote

August 23, 200916 yr

As Si says just persevere till its completely smooth,time consuming but the end result is worth it :)

Quote

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.

Unfortunately, your content contains terms that we do not allow. Please edit your content to remove the highlighted words below.

Reply to this topic...

Followers

Go to topic listing

No registered users viewing this page.

No registered users viewing this page.

Tyre size recommendations

Might be stating the obvious (to some) but something I didn't realise until I started trying to pick tyres for aftermarket wheels is that the profile figure - e.g. 40 - is 40% of the width.
So for a 255/40/17 tyre - diameter is 255mm, profile / side wall is 102mm (40% of 255), and radius is 17inches.
Learning this made it all make a lot more sense to me. I also have this graphic to refer to. Can't recall where I found it but it's now saved on my desktop!

I also wanted a chunky looking tyre with a solid side wall and after going 245(F) / 265 (R) , have since switched back to 235(F) / 255 (R) as I found the handling was noticeable more boggy and I use the car for fast road and track use. For ref, these tyres are on 18" BBS LMs.

By sumshiftyguy · 6 hours ago6 hr
UK Importers Advice

I used Josh @ Gorilla Imports in 2021. My first time importing and was a very good experience.

By sumshiftyguy · 6 hours ago6 hr
Tyre size recommendations

245 on an 8J will look like a balloon on a 8j….. an 8J is only 204mm wide

The tyres you currently have a 2% smaller in diameter and circumference that the OEM wheel/tyre combo

Personally would be looking at a 225/45r17. Plenty of very nice tyre options and only 0.4% different diameter from OEM size

By nickz32 · 17 hours ago17 hr
Simply Japanese at Beaulieu 19th July 2026

If I’ve built and installed my engine by then (which I bloody hope I have!) I’ll be there

By nickz32 · 17 hours ago17 hr
Suggestions for Potential Valved Exhaust

Personally I wouldn't bother mate!
Valved systems are fine where they are an OEM fit on new cars, but why waste cash trying to replicate that on an older car which sounds pretty decent from the box.
Go and speak to Infinity (the guys next to Jim) and get them to custom build a "normal" system for you. I did and I am very pleased with the result.
My old Mongoose was too intrusive at cruising speeds, so Infinity fabricated one with extra resonators at the front, which made cruising quieter from inside the car. They then used smaller silencers at the rear, so the best of the noise is out back. If I want to have a little fun and enjoy the rumble, I just open the windows.
No fancy switches to mess around with, it looks good, sounds good (without the added knob-headed attention seeking function) and only cost £600 all in.

By RichardS · 17 hours ago17 hr

Sign In

Anyone recommend a good high fill primer?

Featured Replies

Join the conversation

Recently Browsing 0

Recently Browsing 0

Popular Posts

Tyre size recommendations

UK Importers Advice

Tyre size recommendations

Simply Japanese at Beaulieu 19th July 2026

Suggestions for Potential Valved Exhaust

Important Information

Account

Navigation

Search

Configure browser push notifications

Chrome (Android)

Chrome (Desktop)

Safari (iOS 16.4+)

Safari (macOS)

Edge (Android)

Edge (Desktop)

Firefox (Android)

Firefox (Desktop)