Is this 99 spec spoiler oem or not?

Followers

November 28, 200520 yr

http://www.getgreddy.co.uk/shop/product_info.php?products_id=179&osCsid=9c305c82a294aefb9a337d6afb76246f

Quote

November 28, 200520 yr

Speak to Chris @ gergreddy. Its an exact replica of the Spoiler fitted to 1999 and 2000 model 300zx's...as fitted to my zed :dance:

Quote

November 28, 200520 yr

Where can I purchase a OEM 99 spec spoiler?

Quote

November 28, 200520 yr

Nissan (IF they still supply them). Although it will be a LOT more expensive and no different.

Quote

November 28, 200520 yr

What is the OEM version made from?

Quote

November 28, 200520 yr

Probably polyeurothene, which is nice for a Front bumper instead of Fibreglass..but with a rear spoiler I personally dont see the point in paying extra for it.

Quote

November 28, 200520 yr

Why would you want to pay over £1500 for something that you can get (just as good if not better) for a few hundred :confused:

Quote

November 28, 200520 yr

Thanks everyone, think I make a call to Chris.....

Quote

November 28, 200520 yr

Thanks everyone, think I make a call to Chris.....

Drop me a PM or email mate :)

Quote

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.

Unfortunately, your content contains terms that we do not allow. Please edit your content to remove the highlighted words below.

Reply to this topic...

Followers

Go to topic listing

No registered users viewing this page.

No registered users viewing this page.

"Sandwich Plate vs Oil Tree for Sender Placement"

Tried to relocate the Oil Pressure sender using a sandwich plate but i'm not liken it much.
So i'm looking to relocate it again and thought a good place was the capped off branch at the end of the oil tree.
Does anyone know the size and where to find an adaptor so i can put the oil sender here ?

By JaiKai · 11 minutes ago11 min
JaiKai - MK2 - Ziggy Build

ok,
For some reason the oil pump isnt pulling up oil from the sump.
Spoke to Jimmer and he suggested to back fill it from the other side as the pump may be a bit dry.
Need to head now but will give that a bash tomorrow.

By JaiKai · 1 hour ago1 hr
JaiKai - MK2 - Ziggy Build

So i've pulled off the sandwich plate and we have zero oil ?
What the hell is going on as i've now emptied the engine so i can take the filter off again.

By JaiKai · 2 hours ago2 hr
JaiKai - MK2 - Ziggy Build

So think i have discovered my oil pressure issue .
Thinking it may be a Sender issue, i unscrewed the sender expecting a face full of oil and nothing.
Slightly pannicking i undone the sump plug to get a full handle full which is great.

The issue i think is an air trap on the T section of the adaptor i used on the sandwich plate show below.
Going to remove the adaptor and see if oil flows from it, if it doesnt i'll need to take the sandwich plate back off and see whats the issue is.
If there is no oil at the sandwich plate then we have other issues.

By JaiKai · 2 hours ago2 hr
Ignition Coil Pack with pigtail

If you have a broken loom soldering on new plugs is a waste of time & money.Whilst you can,Buy & fit a new engine harness along with a new set of series 2 ethanol resistant injectors from a reputable source.This will future proof against break downs & running faults.

By jimmer · 7 hours ago7 hr

Is this 99 spec spoiler oem or not?

Featured Replies

Join the conversation

Recently Browsing 0

Recently Browsing 0

Popular Posts

"Sandwich Plate vs Oil Tree for Sender Placement"

JaiKai - MK2 - Ziggy Build

JaiKai - MK2 - Ziggy Build

JaiKai - MK2 - Ziggy Build

Ignition Coil Pack with pigtail

Important Information

Account

Navigation

Search

Configure browser push notifications

Chrome (Android)

Chrome (Desktop)

Safari (iOS 16.4+)

Safari (macOS)

Edge (Android)

Edge (Desktop)

Firefox (Android)

Firefox (Desktop)