well i got the front bumper sorted out as to what i want..

 

thats being sorted and modified at the moment..

 

the paints being done by steve at bodywork plus.. so now i just gotta decide on the back end of the car..

 

but this is the general look im after..

Very nice mate! Lamborghini 300ZX Murchulago ???

you gotta love the net..

 

so far i have found,

1 set lambo mirrors for diablo, parallel designs

1 murcielago replica front bumper, lambo kit car ring

1 diablo replica spoiler, parallel designs

a company that can make a set of murcie copy rims for under 2k

lambo look lights, from our man luke at z center

lambo interior trim, silver lady interiors neath

and the gt factory hinges for the doors..

 

now all i gotta do is fit em and have the car painted..

SMOOTH mate, very SMOOTH

 

looks great

 

;)

Looks good that, cant say i like the solid bit on the front bumper where the reg plate is as it wouldnt aid the cooling very well, but other than that, sssssssssssmmmmmmmmooooooooooooooooveee!!

thought about that chunk, that solid bit is actually fine steel grill mesh, painted the same colour, just gives the impression of a solid piece.

 

otherwise i could make some ducts to angle the airflow from the openings into the filter if need be

That looks fookin awsome PK. Is that the real colour that the car is going to be? I think its got a nice hint of Aston in there somewhere. The rear end looks nice like it is. If you are going to spoiler it then raised but small would compliment it mate IMO.

nicest front bumper iv seen, look forward to seeing pics of it completed

yes thats the colour, prehaps a shade out, but steve at bodywork plus assures me he can mix the labmorghini paint for me.

 

as for the spoiler, i have got some nice 100mm through hydraulic rams and im thinking of modding the spoiler to fit on them and use a small tyre compressor with a valve kit and switches to raise lower the spoiler.

 

i can provide piccies of rams tmrw, camera battery needs chargin.. again!

 

i desperatly need some piccies of tail tubs, be nice to get a piccie of a strosek tub, but any will do, i will need various angles etc though...

will put indicator led's in the new door mirrors when fitted..

 

will have to as i will need to remove them when the gt hinges are fitted..

Are you gonna paint the door mirror plates

not sure, that may be over kill i will have totake a look in photy shopp, but then saying that.. the door pillars that the windows run in might look nice painted too.. hmmm, bugger .. you got me thinkin now!

looks good mate are the big openings so you can fit small cows in to cook them as you drive along?

:tongue: :tongue: cheeky foookker! :tongue: :tongue:

the front on view .. sorta.. bit wonky but gettin there.. gotta take some more pics of car at same angles as piccies of bumper i have got..

thought about that chunk, that solid bit is actually fine steel grill mesh, painted the same colour, just gives the impression of a solid piece.

 

otherwise i could make some ducts to angle the airflow from the openings into the filter if need be

 

Carefull with the Fine Mesh...at speed it will actually act as a solid barrier from the air presure, preventing any airflow getting through.

 

You could find that the two side air ducts provide plenty of cooling to the intercoolers, and any special ducts you make for the Airfilter will work....but the Rad itself would not receive any air at all.

Carefull with the Fine Mesh...at speed it will actually act as a solid barrier from the air presure, preventing any airflow getting through.

 

You could find that the two side air ducts provide plenty of cooling to the intercoolers, and any special ducts you make for the Airfilter will work....but the Rad itself would not receive any air at all.

 

 

the mesh wont be so fine as to allow that to happen, im also toying with the idea of a small vent section blow the numberplat that vents onto the filter..

very nice!!!