Ticking noise from underneath???

Followers

April 22, 200421 yr

Hi,

I have recently noticed a ticking noise coming from under the car about half way along. Pretty much about where the drivers seat is.

I know I have a dodgy prop bearing and have a new one on the way from the States at the moment.

Could this noise just be the centre bearing really on its last legs or is there another problem lurking from under my Zed?

Any ideas?

Justin.

Quote

April 22, 200421 yr

Have you still got the cats in mate..?? if you have it might be one of them cracking the honey comb in side and on its way out...:(

Quote

April 23, 200421 yr

Author

Have you still got the cats in mate..?? if you have it might be one of them cracking the honey comb in side and on its way out...:(

Hi,

I have got the cats in. I don't know if it is that though. It seems like more of a mechanical ticking.

If you are right though I guess it is a good excuse for a decat :dance:

Justin

Quote

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.

Unfortunately, your content contains terms that we do not allow. Please edit your content to remove the highlighted words below.

Reply to this topic...

Followers

Go to topic listing

No registered users viewing this page.

No registered users viewing this page.

Check engine light comes on and off sporadic.

Those codes are all pointing at a related issue. A/F ratio falling out of range, heater elements within the O2's out of temp range, EGR sensor or exhaust gas temp falling out of range, etc. There is a few areas to consider...
Was any work recently done to the car that may have triggered this? When was the last time you replaced the O2 sensors? Check the O2 connectors and wiring to make sure one of them hasn't contacted the exhaust or melted. Any exhaust leaks especially before the cats? When was the last time you performed an induction service and cleaned the intake, TBs, IAC, etc? The EGR and IACV love to get carbon buildup over the years and can affect flow, similarly can happen to the vac lines to the factory wastegate control solenoid. You mentioned the car felt like it was still running well, so no idle RPM fumbling, hanging, stumbling, etc? Are you running an aftermarket boost control solenoid or OEM? Sorry for the load of questions, but need a bit more to go off of to help point you in the right direction.
Even though the vehicle has considerable low mileage, it's still 30 years old. If it's kept in a garage it tends to handle the elements better than sitting out in the external environmental conditions and will need more routine maintenance and care regardless if it's being driven or not. (i.e. 60K / 120k maint w/ timing belt)

By protoj · Yesterday at 18:481 day
JaiKai - MK2 - Ziggy Build

Time to clean the AC parts as i found a birds nest in it.

By JaiKai · Yesterday at 12:041 day
Check engine light comes on and off sporadic.

Hello, I have a 1996 twin turbo manual with 64k miles. I recently started having the check engine light come on sometimes and other times it doesn't. When I checked the codes these are what I got : If anyone has had these same codes what did they change to fix the problem. Car runs fine with check engine light on but want to fix issue. Any help would be greatly appreciated. Thank you.
P0400
P0136
P1150
P1155

By JB300ZXTT · Monday at 22:141 day
UK Importers Advice

Thanks for the recommendations, few different places recommended Gorilla so I will get in touch with them.

By CarmageddonTheMusical · Sunday at 13:333 days
Reverse switch problem

Me again.
Reverse lights don’t work. Checked the bulbs and the fuse by the drivers pedal, all seem fine.
So I assume it’s the reverse switch. I’ve bought a spare and tried to swap it today. What a pain that is! I failed.

So I have two questions:
Is this possible without dropping the gearbox?
I wanted to test it was definitely the switch before I went crazy getting it out, so unplugged the old one and plugged the new one in, put car in reverse and switched on ignition and then pressed the end of the switch in but it still didn’t turn the lights on. Does the switch work this way? That you can push the plunger end in and it should turn on?

By RobHowl · Saturday at 21:213 days

Sign In

Ticking noise from underneath???

Featured Replies

Join the conversation

Recently Browsing 0

Recently Browsing 0

Popular Posts

Check engine light comes on and off sporadic.

JaiKai - MK2 - Ziggy Build

Check engine light comes on and off sporadic.

UK Importers Advice

Reverse switch problem

Important Information

Account

Navigation

Search

Configure browser push notifications

Chrome (Android)

Chrome (Desktop)

Safari (iOS 16.4+)

Safari (macOS)

Edge (Android)

Edge (Desktop)

Firefox (Android)

Firefox (Desktop)