Parts # For a petrol filler pipe heat shield

Posted August 7, 20168 yr

does any1 know the parts number For a petrol filler pipe heat shield, cheers

Quote

August 7, 20168 yr

Quote

August 7, 20168 yr

http://nissan4u.com/parts/300zx/el_z32/1990_1/type_1/fuel_and_engine_control/fuel_tank_and_fuel_piping/illustration_4/

She's so fine, there's no tellin' where the money went - Simply irresistible.

Quote

August 7, 20168 yr

Author

cheers andrew your a life saver ,been hunting for over an hour and a half trying to find the numbers :clap:

Quote

August 7, 20168 yr

http://www.ebay.co.uk/itm/300ZX-Z32-parts-FUEL-FILLER-PIPE-SHIELDS-1990-to-1999-/272319917770?_trksid=p2141725.m3641.l6368

one on ebay....

Watching my Z disintegrate on my driveway!!!

Quote

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.

Unfortunately, your content contains terms that we do not allow. Please edit your content to remove the highlighted words below.

Reply to this topic...

https://www.300zx-owners.club/forums/topic/154288-parts-for-a-petrol-filler-pipe-heat-shield/

Followers

Go to topic listing

No registered users viewing this page.

No registered users viewing this page.

Clutch issue after car standing for a long time..

I had a similar problem and solved it with a piece of 4 x 2 held in place by the seat overnight to depress the clutch, May have been an old wives tale to bleed the system but it worked for me

By A 2X OK · 20 hours ago20 hr
Clutch issue after car standing for a long time..

Update - left it for a while and pumped the clutch repeatedly to get the pressure back up. Now changing into all gears again 🥰
Next job is to swap out the instrument cluster for a new one and prep it for an MOT.
Then I'll just need to remember how to drive a manual again! 😂
CheerZ
Steve 🙂

By cybernet · 21 hours ago21 hr
Clutch issue after car standing for a long time..

Happy Friday all!
I've finally started work on my Zed! It has sat in my garage since 2013 with only a couple of engine warm ups. The last time I turned her over was July 2023 when I discovered that my braided fuel lines had started to perish and were pissing fuel all over the engine bay. Fuel lines have now been replaced along with a new battery, oil, coolant and fuel. Pleased to report she's now starting up and idling fairly well.
However, I went to move her out of the garage for the first time today and was unable to engage reverse gear. Clutch pedal feels ok but there's more travel than I remember before it hits resistance. I've found that I can get the car in gear with the engine off, but not when it's running. An RPS Twin turbo MAX Street Clutch was fitted around 800 miles ago (in 2009!). Assuming this points to slave cylinder, but would welcome any suggestions before I start heading off down a blind alley!
CheerZ
Steve 🙂

By cybernet · Posted Yesterday at 12:491 day
Trip to Brands Hatch

By JaiKai · Monday at 15:514 days
Trip to Brands Hatch

Also spotted this zed

By JaiKai · Monday at 15:494 days

Sign In

Parts # For a petrol filler pipe heat shield

Featured Replies

Join the conversation

Recently Browsing 0

Recently Browsing 0

Popular Posts

Clutch issue after car standing for a long time..

Clutch issue after car standing for a long time..

Clutch issue after car standing for a long time..

Trip to Brands Hatch

Trip to Brands Hatch

Important Information

Account

Navigation

Search