My Zds dead.....

Followers

October 28, 200223 yr

My 91 fairlady TT has died...desperately seeking an engine, anything concidered.....Overheated on the M4. Its not her time to go now.. Any help would be greately apreciated by me and my mourning familly.. I hope i dont sound to desperate but its a sad loss.

Quote

October 29, 200223 yr

Why do you need a new engine? The VG30 is quite resilient to over heating. Oh and where abouts are you???

CheerZ,

Andy

Quote

October 29, 200223 yr

I HAVE JUST PUT A POST UP IN FOR SALE AND WANTED SELLING MY 90 TT JAP ENGINE WITH VIDEO OF IT RUNNING, STILL IN CHASSIS WITH LOADS OF OTHER PARTS ON IT IF YOU STILL NEED AN ENGINE? IM ASKING £700 FOR FOR SOMEONE TO TAKE IT AWAY MY NUMBER IS 01278794348

OR 07761186904

PHIL

Quote

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.

Unfortunately, your content contains terms that we do not allow. Please edit your content to remove the highlighted words below.

Reply to this topic...

Followers

Go to topic listing

No registered users viewing this page.

No registered users viewing this page.

"Sandwich Plate vs Oil Tree for Sender Placement"

Tried to relocate the Oil Pressure sender using a sandwich plate but i'm not liken it much.
So i'm looking to relocate it again and thought a good place was the capped off branch at the end of the oil tree.
Does anyone know the size and where to find an adaptor so i can put the oil sender here ?

By JaiKai · 33 minutes ago33 min
JaiKai - MK2 - Ziggy Build

ok,
For some reason the oil pump isnt pulling up oil from the sump.
Spoke to Jimmer and he suggested to back fill it from the other side as the pump may be a bit dry.
Need to head now but will give that a bash tomorrow.

By JaiKai · 2 hours ago2 hr
JaiKai - MK2 - Ziggy Build

So i've pulled off the sandwich plate and we have zero oil ?
What the hell is going on as i've now emptied the engine so i can take the filter off again.

By JaiKai · 2 hours ago2 hr
JaiKai - MK2 - Ziggy Build

So think i have discovered my oil pressure issue .
Thinking it may be a Sender issue, i unscrewed the sender expecting a face full of oil and nothing.
Slightly pannicking i undone the sump plug to get a full handle full which is great.

The issue i think is an air trap on the T section of the adaptor i used on the sandwich plate show below.
Going to remove the adaptor and see if oil flows from it, if it doesnt i'll need to take the sandwich plate back off and see whats the issue is.
If there is no oil at the sandwich plate then we have other issues.

By JaiKai · 3 hours ago3 hr
Ignition Coil Pack with pigtail

If you have a broken loom soldering on new plugs is a waste of time & money.Whilst you can,Buy & fit a new engine harness along with a new set of series 2 ethanol resistant injectors from a reputable source.This will future proof against break downs & running faults.

By jimmer · 8 hours ago8 hr

My Zds dead.....

Featured Replies

Join the conversation

Recently Browsing 0

Recently Browsing 0

Popular Posts

"Sandwich Plate vs Oil Tree for Sender Placement"

JaiKai - MK2 - Ziggy Build

JaiKai - MK2 - Ziggy Build

JaiKai - MK2 - Ziggy Build

Ignition Coil Pack with pigtail

Important Information

Account

Navigation

Search

Configure browser push notifications

Chrome (Android)

Chrome (Desktop)

Safari (iOS 16.4+)

Safari (macOS)

Edge (Android)

Edge (Desktop)

Firefox (Android)

Firefox (Desktop)