Eastenders again..........zzzzzz............

Followers

April 30, 200223 yr

Anybody know where I can a set of Brembo

drilled front discs from?

Enquired at Brembo Notrh America but the

shipping was dearer than the discs!!

Quote

April 30, 200223 yr

Got mine from http://www.eliteauto.ca/ Asked them to ship surface rather than air, which takes forever but is cheaper and you usually avoid the import tax & VAT (I did).

Quote

April 30, 200223 yr

Author

Cheers Andy

How much did yours work out at?

Quote

April 30, 200223 yr

Well I bought then via eBay and due to a small cock-up (I thought the price was in CA$ not US$) what appeared to be an amazing bargain turned out to be just a bargain.

I think I paid about £270 for a set of four discs including shipping.

Quote

April 30, 200223 yr

Author

That sounds good, I`ll give them a try.

Shame you cant get the callipers for the same money!

Quote

May 1, 200223 yr

Try 3G brakes in this country. http://www.3gbrakes.co.uk

speak to Kevin.

They do the full brembo range for stock size discs.

Alternatively go for the upgraded Skyline package.

Quote

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.

Unfortunately, your content contains terms that we do not allow. Please edit your content to remove the highlighted words below.

Reply to this topic...

Followers

Go to topic listing

No registered users viewing this page.

No registered users viewing this page.

Check engine light comes on and off sporadic.

Those codes are all pointing at a related issue. A/F ratio falling out of range, heater elements within the O2's out of temp range, EGR sensor or exhaust gas temp falling out of range, etc. There is a few areas to consider...
Was any work recently done to the car that may have triggered this? When was the last time you replaced the O2 sensors? Check the O2 connectors and wiring to make sure one of them hasn't contacted the exhaust or melted. Any exhaust leaks especially before the cats? When was the last time you performed an induction service and cleaned the intake, TBs, IAC, etc? The EGR and IACV love to get carbon buildup over the years and can affect flow, similarly can happen to the vac lines to the factory wastegate control solenoid. You mentioned the car felt like it was still running well, so no idle RPM fumbling, hanging, stumbling, etc? Are you running an aftermarket boost control solenoid or OEM? Sorry for the load of questions, but need a bit more to go off of to help point you in the right direction.
Even though the vehicle has considerable low mileage, it's still 30 years old. If it's kept in a garage it tends to handle the elements better than sitting out in the external environmental conditions and will need more routine maintenance and care regardless if it's being driven or not. (i.e. 60K / 120k maint w/ timing belt)

By protoj · 13 hours ago13 hr
JaiKai - MK2 - Ziggy Build

Time to clean the AC parts as i found a birds nest in it.

By JaiKai · 20 hours ago20 hr
Check engine light comes on and off sporadic.

Hello, I have a 1996 twin turbo manual with 64k miles. I recently started having the check engine light come on sometimes and other times it doesn't. When I checked the codes these are what I got : If anyone has had these same codes what did they change to fix the problem. Car runs fine with check engine light on but want to fix issue. Any help would be greatly appreciated. Thank you.
P0400
P0136
P1150
P1155

By JB300ZXTT · Monday at 22:141 day
UK Importers Advice

Thanks for the recommendations, few different places recommended Gorilla so I will get in touch with them.

By CarmageddonTheMusical · Sunday at 13:332 days
Reverse switch problem

Me again.
Reverse lights don’t work. Checked the bulbs and the fuse by the drivers pedal, all seem fine.
So I assume it’s the reverse switch. I’ve bought a spare and tried to swap it today. What a pain that is! I failed.

So I have two questions:
Is this possible without dropping the gearbox?
I wanted to test it was definitely the switch before I went crazy getting it out, so unplugged the old one and plugged the new one in, put car in reverse and switched on ignition and then pressed the end of the switch in but it still didn’t turn the lights on. Does the switch work this way? That you can push the plunger end in and it should turn on?

By RobHowl · Saturday at 21:213 days

Sign In

Eastenders again..........zzzzzz............

Featured Replies

Join the conversation

Recently Browsing 0

Recently Browsing 0

Popular Posts

Check engine light comes on and off sporadic.

JaiKai - MK2 - Ziggy Build

Check engine light comes on and off sporadic.

UK Importers Advice

Reverse switch problem

Important Information

Account

Navigation

Search

Configure browser push notifications

Chrome (Android)

Chrome (Desktop)

Safari (iOS 16.4+)

Safari (macOS)

Edge (Android)

Edge (Desktop)

Firefox (Android)

Firefox (Desktop)