As the title states, is £50 a good price foor a hub and wheel bearing??

 

But more importantly to save money and effort - is it possible to just replace a hub Pin on its own??

Sounds about right..

Is that delivered?

Yup! Do you know if you can just replace a pin though? ..i damaged one of the pins removing a spacer so that is all i need to replace, but the pin looks like it is welded on.

do you mean one of the threaded studs?

I've got all that on my breaker!! Feel free to have a look!

Yup! Do you know if you can just replace a pin though? ..i damaged one of the pins removing a spacer so that is all i need to replace, but the pin looks like it is welded on.

 

If you mean the wheel stud as below, then they are only a few quid each and are easy to knock out and pull a new one through using washers and the wheel nut, if you mean the lower arm ball joint, then they can also be changed individially too, just held in by a snap ring.

 

Jeff TT

 

 

http://www.twinturbo.net/nissan/300zx/FAQ/FAQpages/wheelstud.html

Yes apologies I mean the stud. Spot on, thanks very much guys :bow: -

 

Where abouts can i get a stud from??

a stud shop :lol:

 

dunno matey, nissan (bleh), or probably most motor factors if you take your old one with you, a wheel is stud is probably the only part for a car I haven't had to buy/fit!

You can come round to mine and knock one out.

 

Oh no, that sounds terrible!

 

You can pull one of my studs off.

 

Erm not sure if that sounds just as bad.

 

You can bash one out at mine if you like. It may be old but I'm sure it's still hard enough to do the job.

 

Oh for Gods sake this is getting worse!

 

Tell you what, I'll Knock one off here for you and then I'll come round to yours and I can hammer it in from the back and pull it the rest of the way by tightening your nuts.

 

I give up!

You can come round to mine and knock one out.

 

Oh no, that sounds terrible!

 

You can pull one of my studs off.

 

Erm not sure if that sounds just as bad.

 

You can bash one out at mine if you like. It may be old but I'm sure it's still hard enough to do the job.

 

Oh for Gods sake this is getting worse!

 

Tell you what, I'll Knock one off here for you and then I'll come round to yours and I can hammer it in from the back and pull it the rest of the way by tightening your nuts.

 

I give up!

:lol::lol::lol::lol::lol::lol::lol::lol::lol:

You can come round to mine and knock one out.

 

Oh no, that sounds terrible!

 

You can pull one of my studs off.

 

Erm not sure if that sounds just as bad.

 

You can bash one out at mine if you like. It may be old but I'm sure it's still hard enough to do the job.

 

Oh for Gods sake this is getting worse!

 

Tell you what, I'll Knock one off here for you and then I'll come round to yours and I can hammer it in from the back and pull it the rest of the way by tightening your nuts.

 

I give up!

 

:offtopic: :ban: :xxx:

haahaaaaaa :lol: !! ...i'll just go to this stud shop then!

 

naa, that would be awesome if i could nab one of your studs, cheers mate :)

 

ive got that tonne for your wings ready & waiting now mate.

 

...any chance you could give us a hand getting this last nut off holding the bumper on, as its need the flexible socket to get to it as i almost rounded the barsteward trying to get at it :headvswal

Yes no probs give me a call mate!

Nice one, will do! Ive got busy shifts till next week so Tues is probs best but i'll give you a bell nearer the time!!

Thread rezerection!! where were u getting the hub and bearing at £50? was that second hand?

Thread rezerection!! where were u getting the hub and bearing at £50? was that second hand?

 

you looking for a hub and bearing i know a man thats got 4 off:wink:

yeah think mine are warped. are they in good nick mate?