trebor

Issue resolved. Best guess, it was a dirty air filter causing a sensor to sense low flow and disabling ignition. I don’t know if there is such a system but with the intakes open at the cylinder head she fired up.

Afternoon all, Looking for some advice as I stand on the forecourt of a garage in Malta. I drove the car here, warmed down the turbos then turned off the ignition. On restart (10 minutes elapsed), I disabled the immobiliser as normal and cranked the engine as normal. No fire up. I am yet to pull a plug and check for a spark but fuel pump runs, I can smell fuel but not too strongly, all fuses are good. I interchanged EGI and ignition coil relays with no effect. Has anyone experienced anything similar? Rob +447703237954

View Advert Uk Spec, Twin Turbo, Manual in Grey metallic, 1994. 1994, UK Spec, Nissan 300zx Z32, Twin Turbo, manual transmission. Full leather and suede trim interior. Vehicle has very few modifications. A one piece drive shaft, uprated clutch, stainless steel exhaust system, 99 spec rear spoiler. Otherwise unmolested throughout its lifetime. The mileage is a very genuine 127000 miles. The engine had an overhaul at 125,000 miles. The service history I hold dates back to 1997. I suspect the services from 1994 to 1996 were Nissan dealer services but although I have the original Nissan wallet there is no service document amongst the manuals etc. I have owned the car since 2005. There has been about 5000 miles put on since then however I have always run the engine and carried out functional checks monthly. I am an aircraft engineer and I understand the importance of maintenance. Defects: Crack in windscreen however not an MOT fail. Passenger heated seat. Air-conditioning. Radio Antenna. Cruise control. I have not find the time 18 years to troubleshoot these defects that were present when I bought the car. For any further information please get in touch. I have a club valuation of £26,000 and I am open to offers. Advertiser trebor Date 13/07/23 Price Category Cars - For Sale  

Thank you, that's great.

Hi all, I am finally ready to start putting the work into my Z. Its been garaged since 2014. Its mostly original and I intend to keep it that way. Please could you recommend places to purchase OEM spares. I need to replace all the brake lines, hose and pipe. Any recommendations for hard pipe and fittings? Running gear has corrosion and I'll need to replace that which cannot be cleaned up. Yours hopefully Rob

Many thanks

Afternoon, I read the post and the reference to the Standard wheel, tyres. I want to put my standard, UK spec, wheels back on the car. I am looking for advice on a set of tyres as it seems difficult to get a set made by a single manufacturer. Please could you tell me what you found for your car and how do they perform? Anyone with recommendations on mixing tyres sets? THanks Rob

Thanks Legrath.

Its all going to be on the never never so moneys no object ! I dont have a budget as yet. I wanted to cost the different options then make a call.

Hi All My right exhaust bank has begun to churn out the blue smoke. Can you please advise me: What spares I will need once I have the engine out. Where I can get them from the UK. Should I be re-conditioning the turbos entirely ? How do aftermarket replacement turbos compare price wise to re-conning the original items. If I were to have a garage undertake the work, how much do you think it would cost? Many thanks Rob

Thanks, I have done.

Evening all, Does anyone have any information on camping at Oulton park for modified live next week ? Thanks Rob

Thanks.

Thanks Jimmy. So one click for sports mode then? Amazing. Will I have had a fault indication is it were goosed?

Evening, I began stripping out my Z boot trim today to replace the rear shock struts and was surprised to find an electrical actuator sat on top of each shock. Looking in the manual and comparing to my car though, I dont have the suspension adjustment control on the centre console. My question to the Z gurus is was this normal fit for a UK, manual, twin turbo ,1994 ? I cant understand how the equipment would be fitted but not the control panel? Does anyone know?