dusty

cheers guys i'll look into them this weekend, much appreciated

Its a 91 tt jap import manual

Hi, I am having idle problems whenever I go to slow down and stop the car. The car keeps trying to cut out and sometimes does. Its ok when first started but soon starts to play up :huh:. Has anyone got any idea on what the prob can be and how to sort it out...? Cheers Jay

yes in deed, is this colour specific to the car then?

yes in deed, is this colour specific to the car then?

I have a 91 import zx and it has TWEED SEATS!! anyway I would love to replace them at somepoint with leather but I don't have the money at the moment. I was just wondering what i could do to reapair the seat for the time being. Its a blue grey tweed seat and the rip is where they normally go on the right hand side of the drivers bolster. Everytime I get in and out of the car foam from the seat just flakes of onto the floor and its really annoying and looks rubbish, so what can i do? cheers people :rockon:

not done much as not long got my first Z. I have put a Japspeed free flow cat back system with decats, fitted a Exedy clutch kit NSK2174, front and rear dimpled grooved brake discs and pads and fitted dump valves. Not to sure of where to go next from that, thats why i have been thinking of maybe a chip/remapp, was going to get a front mounted intercooler at somepoint. what would you suggest?

Hi, really interested in increasing the power of my 91 jap import manual tt but not really to sure how to do it... was thinking of an chipped ecu but don't have a clue about them or even fitting one :huh:. I've seen this on ebay http://cgi.ebay.co.uk/Nissan-300ZX-TwinTurbo-400-BHP-Performance-Chip-Tuning-/230534164836?pt=UK_CarsParts_Vehicles_CarParts_SM&hash=item35ace83164 but not to sure about it. Does anybody know anything about these things who could help? cheers Jay

I managed to drill out the snapped studs on my downpipes with what ever drill bits i had in the garage i did take a few hours and a lot of bits but persistance paid off. I jacked the car up put the axle stands under plugged in the old electric drill got the junior hacksaw layed under the car with no room to move. Hacksawed the studs flush, pin punched a centre hole then drilled a whole all the way through with a 4mm drill bit. (You may want to wear some saftey glasses as you do get a lot of hot shardes of metel fall down). Then went up in sizes to the size of the new nut and bolt. One thing that happend to me which I stress to try not to do is brake a drill bit whil'st drilling the thread out!! As it is a absolute nightmare to then drill out the broken bit!! so be carefull. Its a big relief when you drill them out and fit the new bolts! My neck was really stiff the next day but was well worth it.

hi, I recently replaced the pas pump on my 91 import 300zx tt as the old one was making some strange noises. But what i want to know is what do I do with the old one.... Can it be repaired and be of any use to anyone? or should I just get it gone and weigh it in? jay

Bump!

cool thats about an hour and a bit from me. thanks, getting closer.

cheers mark, hoping to find something a bit nearer to me as i would have to trailer the car over to you. if i can't find anything nearer then i will contact you and make arrangments. cheers J

Hi all, having spent a while replacing the slave cylinder and assoc pipework on my 91 300zxtt I have found that I still have a sliping clutch and am in definite need of a new clutch. Being relatively new to my car I am not confident in undertaking a clutch change. I wondered if anyone can reccommend a garage or individual somewhere in the Kent area who could undertake this kind of work for an affordable price? I am in Ramsgate, Kent but could drive the car carefully a reasonable distance if required, especially if it could be done in a day? If anybody can offer some advice I would be very grateful. Cheers Jay