Spartan-117

43 - 50 (4.4 - 5.1, 32 - 37) N.m (kg-m, ft-lb) for the two seater turbo, but it should be around the same for most of the models

Hi all, Just refitted my gearbox after changing the clutch but im not sure its working correctly. SHould the drive shaft (seen form the back of the gearbox where the propshaft connects) always be spinning? It seems to stop when i put the clutch down which i assume is correct just need a little help on this as i'm physically and mentally broken after getting the gearbox back on Cheers

thanks, will get some on order. When I did the s13 i had to get a garage to press it out in the end but fingers crossed for the Z

is it the same ball joint as the hicas one, its the only one i could find: https://www.zcentre.co.uk/index.php/click-here-for-parts/suspension-steering/300zx-rear-nissan-oem-outer-track-rod-ball-joint

struggling to find the info, so appologies in advance 300zx manual tt (1992) Have play in the rear wheels and was planning to replace the lower ball joints on the arm, but I cant find any info if they can be replaced or not. On my old s13 it was always just replace the ball joint. do i have to but the whole arm or can the ball joint be replaced?? its this part:

Evening all, After a year getting my car back together and before its maiden voyage, the clutch is behaving strange!! when the engine is OFF, the car will select gear no problem. When the engine is ON, the clutch goes super loose and i cant get into gear (the pedal does not get stuck to the floor btw). All fluid levels are ok. Car has been sitting for several months. Any help would be much appreciated, was hoping to go for a drive tomorrow

yes thats correct, 0 to 0. When I first lined it up, it looked right to the pictures I had seen which is why I got confused. Fisicly checking the piston TDC was a big help to get it right. I have changed the timing belt before, so I dont know why I messed it up this time!!

all sorted now after talking to jeff from zworld. He said to stick a long screw driver down the sparkplug hole on cylinder 1 so I could see where tdc was when I turned the crank and it turned out the lower crank was not lined up as well as I thought :(. After I reset the timing belt with the aid of the screw driver the main pulley marks lined up correctly. Thanks to jeff and u guys for the help

took the covers off and the main pulley again. the marks all line up as they should so i'm now really confused if the main pulley should be -10 out from 0??

Yes thats with the woodruff key installed. I use the premarked lines to get the timing position right, this includes checking the cams and the pulley marks. I then count the teeth between as spec'ed in the manual. I amumed that the main pulleys 0 mark would line up with the marks on the lower timing belt cover and so was shocked to find the pulley over ( after using the woodruff key)!!! Just wanted to get some assuance before fitting the other stuff back on

just aligned the timing belt and put the main pully back on, but have noticed the main pully mark sitting at around -10 degrees from the 0 mark. Not sure if this is correct or not, I was hopping not to have to strip down the engine front again !! ps. all the belt timing marks were lined up before I put the pully back on cheers

yep tried tthe t-cut with no result, got some anti scratch stuff so i may give that a try

last week my car was covered in tree pollen, was busy so i only had time to jet spray most of the pollen off and dame it don't half stick!! this week end got round to cleaning it proper only to find the pollen has some how eaten into the paint making it look like there's fine speckles of dirt over it. To top it off I only had the rear of the car resprayed late last year :cursing: (was starting to wonder if the bloke just used water colors to paint the car!) so if your car is pollen;ed to **** clean it immediately

found the noise. I was the old down pipe leaking though its cover, just glad it was nothing more serious

yes the noise is present wit the clutch down. Will have to wait for the weekend (and dry weather) to try the aircon pully, have to work :(