is this normal

Followers

April 25, 200718 yr

yesterday i was asking for help re poss boost leak, someone suggested check throttle was'nt snapping shut. this morning starting from cold i noticed left hand throttle cable not moving seems to have same amount of play on it as other one, is this the norm ?

Quote

April 25, 200718 yr

The left hand one is for cruise control so its normal for it not to move in that way.

Quote

April 25, 200718 yr

Author

The left hand one is for cruise control so its normal for it not to move in that way.

thanks bilky, from a total amateur

Quote

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.

Unfortunately, your content contains terms that we do not allow. Please edit your content to remove the highlighted words below.

Reply to this topic...

Followers

Go to topic listing

No registered users viewing this page.

No registered users viewing this page.

Reverse switch problem

Me again.
Reverse lights don’t work. Checked the bulbs and the fuse by the drivers pedal, all seem fine.
So I assume it’s the reverse switch. I’ve bought a spare and tried to swap it today. What a pain that is! I failed.

So I have two questions:
Is this possible without dropping the gearbox?
I wanted to test it was definitely the switch before I went crazy getting it out, so unplugged the old one and plugged the new one in, put car in reverse and switched on ignition and then pressed the end of the switch in but it still didn’t turn the lights on. Does the switch work this way? That you can push the plunger end in and it should turn on?

By RobHowl · 11 hours ago11 hr
Tyre size recommendations

Cheers all,
I did consider a 225/45/17 but thought that it might be too much chunk on the side wall. But so many more options!
Looking at the calculator, going from a 235/40 to a 225/45 is about 7.5mm more sidewall which isn’t much. Loads more choice too. Think I’ll go for that, thanks for the help

By RobHowl · 16 hours ago16 hr
Tyre size recommendations

Use this site or similar to get the rolling circumference difference when you change wheel diameter and tyre profiles.
It will tell you how much the speedo will over or under read, and the difference in overall diameter to work out if they will rub anywhere.
https://tiresize.com/tyre-size-calculator/

By craig · Friday at 22:091 day
Simply Japanese at Beaulieu 19th July 2026

22 hours ago, nickz32 said:If I’ve built and installed my engine by then (which I bloody hope I have!) I’ll be there
Fingers crossed for you Nick!!

By RichardS · Friday at 21:091 day
My daughter calls it Toothless the Dragon: My ‘95 TT Z

Happy to say work on my engine block is now finished! Billet main caps were found to be up to 4 thou out of round. This time they have been machined using the ARP’s that will be used during assembly (unlike last time by EPR!)

Cylinders were rebored to suit my 88mm CP pistons and cross hatching angle, depth and surface finish all set up for the Total Seal gapless piston ring pack I have chosen to use. I think I’ll be the first person on the UK to use Total Seal’s gapless piston rings on a VG30, so I’m looking forward to seeing if the live up to the hype

By nickz32 · Friday at 17:551 day

Sign In

is this normal

Featured Replies

Join the conversation

Recently Browsing 0

Recently Browsing 0

Popular Posts

Reverse switch problem

Tyre size recommendations

Tyre size recommendations

Simply Japanese at Beaulieu 19th July 2026

My daughter calls it Toothless the Dragon: My ‘95 TT Z

Important Information

Account

Navigation

Search

Configure browser push notifications

Chrome (Android)

Chrome (Desktop)

Safari (iOS 16.4+)

Safari (macOS)

Edge (Android)

Edge (Desktop)

Firefox (Android)

Firefox (Desktop)