Part no. for Engine Bay Wiring Loom/Harness?

Followers

September 18, 200124 yr

Have looked on TT.net but can't find it.

My car is a 1991 UK spec. TT Auto.

Vin No:- JN10RGZ32U0002135

SE ordered the part ages ago only to find that it was the wrong loom, so just wondered what the score is?

CheerZ all

Tim

;-)

Quote

September 18, 200124 yr

Bwhahaha i dont even have to reply to that one as it says it all in itself lol.

Timmy i have the wiring harness number at home i shall mail yo tonight with it

Quote

September 18, 200124 yr

CheerZ matey

Tim

;-)

Quote

September 18, 200124 yr

I don't know if there is any AUTO / MANAUL harness difference.

EGI harness, UK manual 2+2 spec car :

24011 40p60 (£330+VAT)

(You can not buy this part from the states)

Detination sesnor harness, not included with the EGI harness!

24078-30p00 ($18)

[This message has been edited by Jez (edited 18-09-2001).]

Quote

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.

Unfortunately, your content contains terms that we do not allow. Please edit your content to remove the highlighted words below.

Reply to this topic...

Followers

Go to topic listing

No registered users viewing this page.

No registered users viewing this page.

Check engine light comes on and off sporadic.

Hello, I have a 1996 twin turbo manual with 64k miles. I recently started having the check engine light come on sometimes and other times it doesn't. When I checked the codes these are what I got : If anyone has had these same codes what did they change to fix the problem. Car runs fine with check engine light on but want to fix issue. Any help would be greatly appreciated. Thank you.
P0400
P0136
P1150
P1155

By JB300ZXTT · 39 minutes ago39 min
UK Importers Advice

Thanks for the recommendations, few different places recommended Gorilla so I will get in touch with them.

By CarmageddonTheMusical · Yesterday at 13:331 day
Reverse switch problem

Me again.
Reverse lights don’t work. Checked the bulbs and the fuse by the drivers pedal, all seem fine.
So I assume it’s the reverse switch. I’ve bought a spare and tried to swap it today. What a pain that is! I failed.

So I have two questions:
Is this possible without dropping the gearbox?
I wanted to test it was definitely the switch before I went crazy getting it out, so unplugged the old one and plugged the new one in, put car in reverse and switched on ignition and then pressed the end of the switch in but it still didn’t turn the lights on. Does the switch work this way? That you can push the plunger end in and it should turn on?

By RobHowl · Saturday at 21:212 days
Tyre size recommendations

Cheers all,
I did consider a 225/45/17 but thought that it might be too much chunk on the side wall. But so many more options!
Looking at the calculator, going from a 235/40 to a 225/45 is about 7.5mm more sidewall which isn’t much. Loads more choice too. Think I’ll go for that, thanks for the help

By RobHowl · Saturday at 17:112 days
Tyre size recommendations

Use this site or similar to get the rolling circumference difference when you change wheel diameter and tyre profiles.
It will tell you how much the speedo will over or under read, and the difference in overall diameter to work out if they will rub anywhere.
https://tiresize.com/tyre-size-calculator/

By craig · Friday at 22:093 days

Sign In

Part no. for Engine Bay Wiring Loom/Harness?

Featured Replies

Join the conversation

Recently Browsing 0

Recently Browsing 0

Popular Posts

Check engine light comes on and off sporadic.

UK Importers Advice

Reverse switch problem

Tyre size recommendations

Tyre size recommendations

Important Information

Account

Navigation

Search

Configure browser push notifications

Chrome (Android)

Chrome (Desktop)

Safari (iOS 16.4+)

Safari (macOS)

Edge (Android)

Edge (Desktop)

Firefox (Android)

Firefox (Desktop)